git.libre-soc.org Git - buildroot.git/blob

   1 >From 9c5fa914202d20756c56e0c4fd76035ed8f8ced8 Mon Sep 17 00:00:00 2001
   2 From: Hans-Christian Egtvedt <hcegtvedt@atmel.com>
   3 Date: Mon, 6 Aug 2007 08:31:14 +0200
   4 Subject: [PATCH 1/1] Add gpio_mouse board setup to atstk1000 board
   5
   6 This patch adds a gpio_mouse_platform_data to the atstk1000 board code and
   7 registers a gpio_mouse platform_device. This will enable a GPIO mouse on header
   8 J1 on GPIO of the ATSTK1000 development kit. The board code is enabled/disabled
   9 in menuconfig.
  10
  11 By connecting J1 (GPIO) to J25 (SWITCH) you can use the following keys to
  12 simulate a mouse:
  13
  14 SW0: right
  15 SW1: down
  16 SW2: up
  17 SW3: left
  18 SW5: right button
  19 SW6: middle button
  20 SW7: left button
  21
  22 Signed-off-by: Hans-Christian Egtvedt <hcegtvedt@atmel.com>
  23 ---
  24  arch/avr32/boards/atstk1000/Kconfig     |   16 ++++++++++
  25  arch/avr32/boards/atstk1000/atstk1002.c |   48 +++++++++++++++++++++++++++++++
  26  2 files changed, 64 insertions(+), 0 deletions(-)
  27
  28 diff --git a/arch/avr32/boards/atstk1000/Kconfig b/arch/avr32/boards/atstk1000/Kconfig
  29 index 718578f..d99d4bd 100644
  30 --- a/arch/avr32/boards/atstk1000/Kconfig
  31 +++ b/arch/avr32/boards/atstk1000/Kconfig
  32 @@ -50,6 +50,22 @@ config BOARD_ATSTK1002_SPI1
  33           GPIO lines and accessed through the J1 jumper block.  Say "y"
  34           here to configure that SPI controller.
  35
  36 +config BOARD_ATSTK1002_GPIO_MOUSE
  37 +       bool "Configure gpio_mouse on GPIO J1 header"
  38 +       depends on !BOARD_ATSTK1002_SW4_CUSTOM
  39 +       help
  40 +         Enable gpio_mouse board configuration on GPIO 0 to 7. Connecting a
  41 +         10-pin flat cable from J1 (GPIO) to J25 (SWITCH) will let a user give
  42 +         mouse inputs using the the switches SW0 to SW7.
  43 +
  44 +         SW0: right
  45 +         SW1: down
  46 +         SW2: up
  47 +         SW3: left
  48 +         SW5: right button
  49 +         SW6: middle button
  50 +         SW7: left button
  51 +
  52  config BOARD_ATSTK1002_J2_LED
  53         bool
  54         default BOARD_ATSTK1002_J2_LED8 || BOARD_ATSTK1002_J2_RGB
  55 diff --git a/arch/avr32/boards/atstk1000/atstk1002.c b/arch/avr32/boards/atstk1000/atstk1002.c
  56 index c958fd4..c7560e5 100644
  57 --- a/arch/avr32/boards/atstk1000/atstk1002.c
  58 +++ b/arch/avr32/boards/atstk1000/atstk1002.c
  59 @@ -17,6 +17,7 @@
  60  #include <linux/types.h>
  61  #include <linux/spi/spi.h>
  62  #include <linux/spi/at73c213.h>
  63 +#include <linux/gpio_mouse.h>
  64
  65  #include <video/atmel_lcdc.h>
  66
  67 @@ -91,6 +92,49 @@ static struct mci_platform_data __initdata mci0_data = {
  68         .wp_pin         = GPIO_PIN_NONE,
  69  };
  70
  71 +#ifdef CONFIG_BOARD_ATSTK1002_GPIO_MOUSE
  72 +static struct gpio_mouse_platform_data gpio_mouse0_data = {
  73 +       .polarity       = GPIO_MOUSE_POLARITY_ACT_LOW,
  74 +       {
  75 +               {
  76 +                       .up             = GPIO_PIN_PB(2),
  77 +                       .down           = GPIO_PIN_PB(1),
  78 +                       .left           = GPIO_PIN_PB(3),
  79 +                       .right          = GPIO_PIN_PB(0),
  80 +                       .bleft          = GPIO_PIN_PB(7),
  81 +                       .bmiddle        = GPIO_PIN_PB(6),
  82 +                       .bright         = GPIO_PIN_PB(5),
  83 +               },
  84 +       },
  85 +       .scan_ms        = 10,
  86 +};
  87 +
  88 +static struct platform_device gpio_mouse0_device = {
  89 +       .name           = "gpio_mouse",
  90 +       .id             = 0,
  91 +       .dev            = {
  92 +               .platform_data = &gpio_mouse0_data,
  93 +       },
  94 +};
  95 +
  96 +static void __init add_device_gpio_mouse0(void)
  97 +{
  98 +       struct platform_device *pdev = &gpio_mouse0_device;
  99 +       struct gpio_mouse_platform_data *data = pdev->dev.platform_data;
 100 +
 101 +       at32_select_gpio(data->up, 0);
 102 +       at32_select_gpio(data->down, 0);
 103 +       at32_select_gpio(data->left, 0);
 104 +       at32_select_gpio(data->right, 0);
 105 +
 106 +       at32_select_gpio(data->bleft, 0);
 107 +       at32_select_gpio(data->bmiddle, 0);
 108 +       at32_select_gpio(data->bright, 0);
 109 +
 110 +       platform_device_register(pdev);
 111 +}
 112 +#endif
 113 +
 114  /*
 115   * The next two functions should go away as the boot loader is
 116   * supposed to initialize the macb address registers with a valid
 117 @@ -321,6 +365,10 @@ static int __init atstk1002_init(void)
 118  #endif
 119  #endif
 120
 121 +#ifdef CONFIG_BOARD_ATSTK1002_GPIO_MOUSE
 122 +       add_device_gpio_mouse0();
 123 +#endif
 124 +
 125         return 0;
 126  }
 127  postcore_initcall(atstk1002_init);
 128 --
 129 1.5.2.3
 130