-@c Copyright (C) 1991, 92, 93, 94, 95, 97, 1998 Free Software Foundation, Inc.
+@c Copyright 1991, 1992, 1993, 1994, 1995, 1997, 1998, 1999, 2000, 2001
+@c Free Software Foundation, Inc.
@c This is part of the GAS manual.
@c For copying conditions, see the file as.texinfo.
@ifset GENERIC
@cindex i386 support
@cindex i80306 support
+@cindex x86-64 support
+
+The i386 version @code{@value{AS}} supports both the original Intel 386
+architecture in both 16 and 32-bit mode as well as AMD x86-64 architecture
+extending the Intel architecture to 64-bits.
+
@menu
* i386-Options:: Options
* i386-Syntax:: AT&T Syntax versus Intel Syntax
-* i386-Opcodes:: Opcode Naming
+* i386-Mnemonics:: Instruction Naming
* i386-Regs:: Register Naming
-* i386-prefixes:: Opcode Prefixes
+* i386-Prefixes:: Instruction Prefixes
* i386-Memory:: Memory References
-* i386-jumps:: Handling of Jump Instructions
+* i386-Jumps:: Handling of Jump Instructions
* i386-Float:: Floating Point
+* i386-SIMD:: Intel's MMX and AMD's 3DNow! SIMD Operations
* i386-16bit:: Writing 16-bit Code
+* i386-Arch:: Specifying an x86 CPU architecture
* i386-Bugs:: AT&T Syntax bugs
* i386-Notes:: Notes
@end menu
@node i386-Options
@section Options
-@cindex options for i386 (none)
-@cindex i386 options (none)
-The 80386 has no machine dependent options.
+@cindex options for i386
+@cindex options for x86-64
+@cindex i386 options
+@cindex x86-64 options
+
+The i386 version of @code{@value{AS}} has a few machine
+dependent options:
+
+@table @code
+@cindex @samp{--32} option, i386
+@cindex @samp{--32} option, x86-64
+@cindex @samp{--64} option, i386
+@cindex @samp{--64} option, x86-64
+@item --32 | --64
+Select the word size, either 32 bits or 64 bits. Selecting 32-bit
+implies Intel i386 architecture, while 64-bit implies AMD x86-64
+architecture.
+
+These options are only available with the ELF object file format, and
+require that the necessary BFD support has been included (on a 32-bit
+platform you have to add --enable-64-bit-bfd to configure enable 64-bit
+usage and use x86-64 as target platform).
+@end table
@node i386-Syntax
@section AT&T Syntax versus Intel Syntax
+@cindex i386 intel_syntax pseudo op
+@cindex intel_syntax pseudo op, i386
+@cindex i386 att_syntax pseudo op
+@cindex att_syntax pseudo op, i386
@cindex i386 syntax compatibility
@cindex syntax compatibility, i386
-In order to maintain compatibility with the output of @code{@value{GCC}},
-@code{@value{AS}} supports AT&T System V/386 assembler syntax. This is quite
+@cindex x86-64 intel_syntax pseudo op
+@cindex intel_syntax pseudo op, x86-64
+@cindex x86-64 att_syntax pseudo op
+@cindex att_syntax pseudo op, x86-64
+@cindex x86-64 syntax compatibility
+@cindex syntax compatibility, x86-64
+
+@code{@value{AS}} now supports assembly using Intel assembler syntax.
+@code{.intel_syntax} selects Intel mode, and @code{.att_syntax} switches
+back to the usual AT&T mode for compatibility with the output of
+@code{@value{GCC}}. Either of these directives may have an optional
+argument, @code{prefix}, or @code{noprefix} specifying whether registers
+require a @samp{%} prefix. AT&T System V/386 assembler syntax is quite
different from Intel syntax. We mention these differences because
almost all 80386 documents use Intel syntax. Notable differences
between the two syntaxes are:
@cindex jump/call operands, i386
@cindex i386 jump/call operands
@cindex operand delimiters, i386
+
+@cindex immediate operands, x86-64
+@cindex x86-64 immediate operands
+@cindex register operands, x86-64
+@cindex x86-64 register operands
+@cindex jump/call operands, x86-64
+@cindex x86-64 jump/call operands
+@cindex operand delimiters, x86-64
@itemize @bullet
@item
AT&T immediate operands are preceded by @samp{$}; Intel immediate
@cindex i386 source, destination operands
@cindex source, destination operands; i386
+@cindex x86-64 source, destination operands
+@cindex source, destination operands; x86-64
@item
AT&T and Intel syntax use the opposite order for source and destination
operands. Intel @samp{add eax, 4} is @samp{addl $4, %eax}. The
source operand, such as the @samp{enter} instruction, do @emph{not} have
reversed order. @ref{i386-Bugs}.
-@cindex opcode suffixes, i386
+@cindex mnemonic suffixes, i386
@cindex sizes operands, i386
@cindex i386 size suffixes
+@cindex mnemonic suffixes, x86-64
+@cindex sizes operands, x86-64
+@cindex x86-64 size suffixes
@item
In AT&T syntax the size of memory operands is determined from the last
-character of the opcode name. Opcode suffixes of @samp{b}, @samp{w},
-and @samp{l} specify byte (8-bit), word (16-bit), and long (32-bit)
-memory references. Intel syntax accomplishes this by prefixing memory
-operands (@emph{not} the opcodes themselves) with @samp{byte ptr},
-@samp{word ptr}, and @samp{dword ptr}. Thus, Intel @samp{mov al, byte
-ptr @var{foo}} is @samp{movb @var{foo}, %al} in AT&T syntax.
+character of the instruction mnemonic. Mnemonic suffixes of @samp{b},
+@samp{w}, @samp{l} and @samp{q} specify byte (8-bit), word (16-bit), long
+(32-bit) and quadruple word (64-bit) memory references. Intel syntax accomplishes
+this by prefixing memory operands (@emph{not} the instruction mnemonics) with
+@samp{byte ptr}, @samp{word ptr}, @samp{dword ptr} and @samp{qword ptr}. Thus,
+Intel @samp{mov al, byte ptr @var{foo}} is @samp{movb @var{foo}, %al} in AT&T
+syntax.
@cindex return instructions, i386
@cindex i386 jump, call, return
+@cindex return instructions, x86-64
+@cindex x86-64 jump, call, return
@item
Immediate form long jumps and calls are
@samp{lcall/ljmp $@var{section}, $@var{offset}} in AT&T syntax; the
@cindex sections, i386
@cindex i386 sections
+@cindex sections, x86-64
+@cindex x86-64 sections
@item
The AT&T assembler does not provide support for multiple section
programs. Unix style systems expect all programs to be single sections.
@end itemize
-@node i386-Opcodes
-@section Opcode Naming
+@node i386-Mnemonics
+@section Instruction Naming
-@cindex i386 opcode naming
-@cindex opcode naming, i386
-Opcode names are suffixed with one character modifiers which specify the
-size of operands. The letters @samp{b}, @samp{w}, and @samp{l} specify
-byte, word, and long operands. If no suffix is specified by an
-instruction then @code{@value{AS}} tries to
+@cindex i386 instruction naming
+@cindex instruction naming, i386
+@cindex x86-64 instruction naming
+@cindex instruction naming, x86-64
+
+Instruction mnemonics are suffixed with one character modifiers which
+specify the size of operands. The letters @samp{b}, @samp{w}, @samp{l}
+and @samp{q} specify byte, word, long and quadruple word operands. If
+no suffix is specified by an instruction then @code{@value{AS}} tries to
fill in the missing suffix based on the destination register operand
(the last one by convention). Thus, @samp{mov %ax, %bx} is equivalent
to @samp{movw %ax, %bx}; also, @samp{mov $1, %bx} is equivalent to
-@samp{movw $1, %bx}. Note that this is incompatible with the AT&T Unix
-assembler which assumes that a missing opcode suffix implies long
+@samp{movw $1, bx}. Note that this is incompatible with the AT&T Unix
+assembler which assumes that a missing mnemonic suffix implies long
operand size. (This incompatibility does not affect compiler output
-since compilers always explicitly specify the opcode suffix.)
-
-Almost all opcodes have the same names in AT&T and Intel format. There
-are a few exceptions. The sign extend and zero extend instructions need
-two sizes to specify them. They need a size to sign/zero extend
-@emph{from} and a size to zero extend @emph{to}. This is accomplished
-by using two opcode suffixes in AT&T syntax. Base names for sign extend
-and zero extend are @samp{movs@dots{}} and @samp{movz@dots{}} in AT&T
-syntax (@samp{movsx} and @samp{movzx} in Intel syntax). The opcode
-suffixes are tacked on to this base name, the @emph{from} suffix before
-the @emph{to} suffix. Thus, @samp{movsbl %al, %edx} is AT&T syntax for
+since compilers always explicitly specify the mnemonic suffix.)
+
+Almost all instructions have the same names in AT&T and Intel format.
+There are a few exceptions. The sign extend and zero extend
+instructions need two sizes to specify them. They need a size to
+sign/zero extend @emph{from} and a size to zero extend @emph{to}. This
+is accomplished by using two instruction mnemonic suffixes in AT&T
+syntax. Base names for sign extend and zero extend are
+@samp{movs@dots{}} and @samp{movz@dots{}} in AT&T syntax (@samp{movsx}
+and @samp{movzx} in Intel syntax). The instruction mnemonic suffixes
+are tacked on to this base name, the @emph{from} suffix before the
+@emph{to} suffix. Thus, @samp{movsbl %al, %edx} is AT&T syntax for
``move sign extend @emph{from} %al @emph{to} %edx.'' Possible suffixes,
thus, are @samp{bl} (from byte to long), @samp{bw} (from byte to word),
-and @samp{wl} (from word to long).
+@samp{wl} (from word to long), @samp{bq} (from byte to quadruple word),
+@samp{wq} (from word to quadruple word), and @samp{lq} (from long to
+quadruple word).
@cindex conversion instructions, i386
@cindex i386 conversion instructions
+@cindex conversion instructions, x86-64
+@cindex x86-64 conversion instructions
The Intel-syntax conversion instructions
@itemize @bullet
@item
@samp{cdq} --- sign-extend dword in @samp{%eax} to quad in @samp{%edx:%eax},
+
+@item
+@samp{cdqe} --- sign-extend dword in @samp{%eax} to quad in @samp{%rax}
+(x86-64 only),
+
+@item
+@samp{cdo} --- sign-extend quad in @samp{%rax} to octuple in
+@samp{%rdx:%rax} (x86-64 only),
@end itemize
@noindent
-are called @samp{cbtw}, @samp{cwtl}, @samp{cwtd}, and @samp{cltd} in
-AT&T naming. @code{@value{AS}} accepts either naming for these instructions.
+are called @samp{cbtw}, @samp{cwtl}, @samp{cwtd}, @samp{cltd}, @samp{cltq}, and
+@samp{cqto} in AT&T naming. @code{@value{AS}} accepts either naming for these
+instructions.
@cindex jump instructions, i386
@cindex call instructions, i386
+@cindex jump instructions, x86-64
+@cindex call instructions, x86-64
Far call/jump instructions are @samp{lcall} and @samp{ljmp} in
AT&T syntax, but are @samp{call far} and @samp{jump far} in Intel
convention.
@cindex i386 registers
@cindex registers, i386
+@cindex x86-64 registers
+@cindex registers, x86-64
Register operands are always prefixed with @samp{%}. The 80386 registers
consist of
the 8 floating point register stack @samp{%st} or equivalently
@samp{%st(0)}, @samp{%st(1)}, @samp{%st(2)}, @samp{%st(3)},
@samp{%st(4)}, @samp{%st(5)}, @samp{%st(6)}, and @samp{%st(7)}.
+These registers are overloaded by 8 MMX registers @samp{%mm0},
+@samp{%mm1}, @samp{%mm2}, @samp{%mm3}, @samp{%mm4}, @samp{%mm5},
+@samp{%mm6} and @samp{%mm7}.
+
+@item
+the 8 SSE registers registers @samp{%xmm0}, @samp{%xmm1}, @samp{%xmm2},
+@samp{%xmm3}, @samp{%xmm4}, @samp{%xmm5}, @samp{%xmm6} and @samp{%xmm7}.
@end itemize
-@node i386-prefixes
-@section Opcode Prefixes
+The AMD x86-64 architecture extends the register set by:
+
+@itemize @bullet
+@item
+enhancing the 8 32-bit registers to 64-bit: @samp{%rax} (the
+accumulator), @samp{%rbx}, @samp{%rcx}, @samp{%rdx}, @samp{%rdi},
+@samp{%rsi}, @samp{%rbp} (the frame pointer), @samp{%rsp} (the stack
+pointer)
+
+@item
+the 8 extended registers @samp{%r8}--@samp{%r15}.
-@cindex i386 opcode prefixes
-@cindex opcode prefixes, i386
+@item
+the 8 32-bit low ends of the extended registers: @samp{%r8d}--@samp{%r15d}
+
+@item
+the 8 16-bit low ends of the extended registers: @samp{%r8w}--@samp{%r15w}
+
+@item
+the 8 8-bit low ends of the extended registers: @samp{%r8b}--@samp{%r15b}
+
+@item
+the 4 8-bit registers: @samp{%sil}, @samp{%dil}, @samp{%bpl}, @samp{%spl}.
+
+@item
+the 8 debug registers: @samp{%db8}--@samp{%db15}.
+
+@item
+the 8 SSE registers: @samp{%xmm8}--@samp{%xmm15}.
+@end itemize
+
+@node i386-Prefixes
+@section Instruction Prefixes
+
+@cindex i386 instruction prefixes
+@cindex instruction prefixes, i386
@cindex prefixes, i386
-Opcode prefixes are used to modify the following opcode. They are used
-to repeat string instructions, to provide section overrides, to perform
-bus lock operations, and to give operand and address size (16-bit
-operands are specified in an instruction by prefixing what would
-normally be 32-bit operands with a ``operand size'' opcode prefix).
-Opcode prefixes are best written on the same line as the instruction
+Instruction prefixes are used to modify the following instruction. They
+are used to repeat string instructions, to provide section overrides, to
+perform bus lock operations, and to change operand and address sizes.
+(Most instructions that normally operate on 32-bit operands will use
+16-bit operands if the instruction has an ``operand size'' prefix.)
+Instruction prefixes are best written on the same line as the instruction
they act upon. For example, the @samp{scas} (scan string) instruction is
repeated with:
@end smallexample
You may also place prefixes on the lines immediately preceding the
-opcode, but this circumvents checks that @code{@value{AS}} does with
-prefixes, and will not work with all prefixes.
+instruction, but this circumvents checks that @code{@value{AS}} does
+with prefixes, and will not work with all prefixes.
-Here is a list of opcode prefixes:
+Here is a list of instruction prefixes:
@cindex section override prefixes, i386
@itemize @bullet
change 32-bit operands/addresses into 16-bit operands/addresses,
while @samp{data32} and @samp{addr32} change 16-bit ones (in a
@code{.code16} section) into 32-bit operands/addresses. These prefixes
-@emph{must} appear on the same line of code as the opcode they modify.
-For example, in a 16-bit @code{.code16} section, you might write:
+@emph{must} appear on the same line of code as the instruction they
+modify. For example, in a 16-bit @code{.code16} section, you might
+write:
@smallexample
addr32 jmpl *(%ebx)
@cindex bus lock prefixes, i386
@cindex inhibiting interrupts, i386
@item
-The bus lock prefix @samp{lock} inhibits interrupts during
-execution of the instruction it precedes. (This is only valid with
-certain instructions; see a 80386 manual for details).
+The bus lock prefix @samp{lock} inhibits interrupts during execution of
+the instruction it precedes. (This is only valid with certain
+instructions; see a 80386 manual for details).
@cindex coprocessor wait, i386
@item
-The wait for coprocessor prefix @samp{wait} waits for the
-coprocessor to complete the current instruction. This should never be
-needed for the 80386/80387 combination.
+The wait for coprocessor prefix @samp{wait} waits for the coprocessor to
+complete the current instruction. This should never be needed for the
+80386/80387 combination.
@cindex repeat prefixes, i386
@item
The @samp{rep}, @samp{repe}, and @samp{repne} prefixes are added
-to string instructions to make them repeat @samp{%ecx} times.
+to string instructions to make them repeat @samp{%ecx} times (@samp{%cx}
+times if the current address size is 16-bits).
+@cindex REX prefixes, i386
+@item
+The @samp{rex} family of prefixes is used by x86-64 to encode
+extensions to i386 instruction set. The @samp{rex} prefix has four
+bits --- an operand size overwrite (@code{64}) used to change operand size
+from 32-bit to 64-bit and X, Y and Z extensions bits used to extend the
+register set.
+
+You may write the @samp{rex} prefixes directly. The @samp{rex64xyz}
+instruction emits @samp{rex} prefix with all the bits set. By omitting
+the @code{64}, @code{x}, @code{y} or @code{z} you may write other
+prefixes as well. Normally, there is no need to write the prefixes
+explicitly, since gas will automatically generate them based on the
+instruction operands.
@end itemize
@node i386-Memory
@cindex i386 memory references
@cindex memory references, i386
+@cindex x86-64 memory references
+@cindex memory references, x86-64
An Intel syntax indirect memory reference of the form
@smallexample
always chooses PC relative addressing for jump/call labels.
Any instruction that has a memory operand, but no register operand,
-@emph{must} specify its size (byte, word, or long) with an opcode suffix
-(@samp{b}, @samp{w}, or @samp{l}, respectively).
+@emph{must} specify its size (byte, word, long, or quadruple) with an
+instruction mnemonic suffix (@samp{b}, @samp{w}, @samp{l} or @samp{q},
+respectively).
+
+The x86-64 architecture adds an RIP (instruction pointer relative)
+addressing. This addressing mode is specified by using @samp{rip} as a
+base register. Only constant offsets are valid. For example:
-@node i386-jumps
+@table @asis
+@item AT&T: @samp{1234(%rip)}, Intel: @samp{[rip + 1234]}
+Points to the address 1234 bytes past the end of the current
+instruction.
+
+@item AT&T: @samp{symbol(%rip)}, Intel: @samp{[rip + symbol]}
+Points to the @code{symbol} in RIP relative way, this is shorter than
+the default absolute addressing.
+@end table
+
+Other addressing modes remain unchanged in x86-64 architecture, except
+registers used are 64-bit instead of 32-bit.
+
+@node i386-Jumps
@section Handling of Jump Instructions
@cindex jump optimization, i386
@cindex i386 jump optimization
+@cindex jump optimization, x86-64
+@cindex x86-64 jump optimization
Jump instructions are always optimized to use the smallest possible
displacements. This is accomplished by using byte (8-bit) displacement
jumps whenever the target is sufficiently close. If a byte displacement
-is insufficient a long (32-bit) displacement is used. We do not support
-word (16-bit) displacement jumps in 32-bit mode (i.e. prefixing the jump instruction
-with the @samp{data16} opcode prefix), since the 80386 insists upon masking
-@samp{%eip} to 16 bits after the word displacement is added.
+is insufficient a long displacement is used. We do not support
+word (16-bit) displacement jumps in 32-bit mode (i.e. prefixing the jump
+instruction with the @samp{data16} instruction prefix), since the 80386
+insists upon masking @samp{%eip} to 16 bits after the word displacement
+is added. (See also @pxref{i386-Arch})
Note that the @samp{jcxz}, @samp{jecxz}, @samp{loop}, @samp{loopz},
@samp{loope}, @samp{loopnz} and @samp{loopne} instructions only come in byte
@cindex i386 floating point
@cindex floating point, i386
+@cindex x86-64 floating point
+@cindex floating point, x86-64
All 80387 floating point types except packed BCD are supported.
(BCD support may be added without much difficulty). These data
types are 16-, 32-, and 64- bit integers, and single (32-bit),
double (64-bit), and extended (80-bit) precision floating point.
-Each supported type has an opcode suffix and a constructor
-associated with it. Opcode suffixes specify operand's data
-types. Constructors build these data types into memory.
+Each supported type has an instruction mnemonic suffix and a constructor
+associated with it. Instruction mnemonic suffixes specify the operand's
+data type. Constructors build these data types into memory.
@cindex @code{float} directive, i386
@cindex @code{single} directive, i386
@cindex @code{double} directive, i386
@cindex @code{tfloat} directive, i386
+@cindex @code{float} directive, x86-64
+@cindex @code{single} directive, x86-64
+@cindex @code{double} directive, x86-64
+@cindex @code{tfloat} directive, x86-64
@itemize @bullet
@item
Floating point constructors are @samp{.float} or @samp{.single},
@samp{.double}, and @samp{.tfloat} for 32-, 64-, and 80-bit formats.
-These correspond to opcode suffixes @samp{s}, @samp{l}, and @samp{t}.
-@samp{t} stands for 80-bit real. The 80387 only supports this format
-via the @samp{fldt} (load 80-bit real to stack top) and @samp{fstpt}
-(store 80-bit real and pop stack) instructions.
+These correspond to instruction mnemonic suffixes @samp{s}, @samp{l},
+and @samp{t}. @samp{t} stands for 80-bit (ten byte) real. The 80387
+only supports this format via the @samp{fldt} (load 80-bit real to stack
+top) and @samp{fstpt} (store 80-bit real and pop stack) instructions.
@cindex @code{word} directive, i386
@cindex @code{long} directive, i386
@cindex @code{int} directive, i386
@cindex @code{quad} directive, i386
+@cindex @code{word} directive, x86-64
+@cindex @code{long} directive, x86-64
+@cindex @code{int} directive, x86-64
+@cindex @code{quad} directive, x86-64
@item
Integer constructors are @samp{.word}, @samp{.long} or @samp{.int}, and
@samp{.quad} for the 16-, 32-, and 64-bit integer formats. The
-corresponding opcode suffixes are @samp{s} (single), @samp{l} (long),
-and @samp{q} (quad). As with the 80-bit real format, the 64-bit
-@samp{q} format is only present in the @samp{fildq} (load quad integer
-to stack top) and @samp{fistpq} (store quad integer and pop stack)
-instructions.
+corresponding instruction mnemonic suffixes are @samp{s} (single),
+@samp{l} (long), and @samp{q} (quad). As with the 80-bit real format,
+the 64-bit @samp{q} format is only present in the @samp{fildq} (load
+quad integer to stack top) and @samp{fistpq} (store quad integer and pop
+stack) instructions.
@end itemize
-Register to register operations should not use opcode suffixes.
+Register to register operations should not use instruction mnemonic suffixes.
@samp{fstl %st, %st(1)} will give a warning, and be assembled as if you
wrote @samp{fst %st, %st(1)}, since all register to register operations
use 80-bit floating point operands. (Contrast this with @samp{fstl %st, mem},
which converts @samp{%st} from 80-bit to 64-bit floating point format,
then stores the result in the 4 byte location @samp{mem})
+@node i386-SIMD
+@section Intel's MMX and AMD's 3DNow! SIMD Operations
+
+@cindex MMX, i386
+@cindex 3DNow!, i386
+@cindex SIMD, i386
+@cindex MMX, x86-64
+@cindex 3DNow!, x86-64
+@cindex SIMD, x86-64
+
+@code{@value{AS}} supports Intel's MMX instruction set (SIMD
+instructions for integer data), available on Intel's Pentium MMX
+processors and Pentium II processors, AMD's K6 and K6-2 processors,
+Cyrix' M2 processor, and probably others. It also supports AMD's 3DNow!
+instruction set (SIMD instructions for 32-bit floating point data)
+available on AMD's K6-2 processor and possibly others in the future.
+
+Currently, @code{@value{AS}} does not support Intel's floating point
+SIMD, Katmai (KNI).
+
+The eight 64-bit MMX operands, also used by 3DNow!, are called @samp{%mm0},
+@samp{%mm1}, ... @samp{%mm7}. They contain eight 8-bit integers, four
+16-bit integers, two 32-bit integers, one 64-bit integer, or two 32-bit
+floating point values. The MMX registers cannot be used at the same time
+as the floating point stack.
+
+See Intel and AMD documentation, keeping in mind that the operand order in
+instructions is reversed from the Intel syntax.
+
@node i386-16bit
@section Writing 16-bit Code
@cindex i386 16-bit code
@cindex 16-bit code, i386
@cindex real-mode code, i386
+@cindex @code{code16gcc} directive, i386
@cindex @code{code16} directive, i386
@cindex @code{code32} directive, i386
-While @code{@value{AS}} normally writes only ``pure'' 32-bit i386 code,
+@cindex @code{code64} directive, i386
+@cindex @code{code64} directive, x86-64
+While @code{@value{AS}} normally writes only ``pure'' 32-bit i386 code
+or 64-bit x86-64 code depending on the default configuration,
it also supports writing code to run in real mode or in 16-bit protected
-mode code segments. To do this, put a @samp{.code16} directive before
-the assembly language instructions to be run in 16-bit mode. You can
-switch @code{@value{AS}} back to writing normal 32-bit code with the
-@samp{.code32} directive.
+mode code segments. To do this, put a @samp{.code16} or
+@samp{.code16gcc} directive before the assembly language instructions to
+be run in 16-bit mode. You can switch @code{@value{AS}} back to writing
+normal 32-bit code with the @samp{.code32} directive.
+
+@samp{.code16gcc} provides experimental support for generating 16-bit
+code from gcc, and differs from @samp{.code16} in that @samp{call},
+@samp{ret}, @samp{enter}, @samp{leave}, @samp{push}, @samp{pop},
+@samp{pusha}, @samp{popa}, @samp{pushf}, and @samp{popf} instructions
+default to 32-bit size. This is so that the stack pointer is
+manipulated in the same way over function calls, allowing access to
+function parameters at the same stack offsets as in 32-bit mode.
+@samp{.code16gcc} also automatically adds address size prefixes where
+necessary to use the 32-bit addressing modes that gcc generates.
The code which @code{@value{AS}} generates in 16-bit mode will not
necessarily run on a 16-bit pre-80386 processor. To write code that
size prefixes.
Note that writing 16-bit code instructions by explicitly specifying a
-prefix or a suffix within a 32-bit code section generates different
-machine instructions than those generated for a 16-bit code segment. In a
-32-bit code section, the following code generates the machine
-instruction sequence @samp{66 6a 04}, which pushes the value @samp{4} onto
-the stack, decrementing @samp{%esp} by 2.
+prefix or an instruction mnemonic suffix within a 32-bit code section
+generates different machine instructions than those generated for a
+16-bit code segment. In a 32-bit code section, the following code
+generates the machine opcode bytes @samp{66 6a 04}, which pushes the
+value @samp{4} onto the stack, decrementing @samp{%esp} by 2.
@smallexample
pushw $4
@end smallexample
The same code in a 16-bit code section would generate the machine
-instruction sequence @samp{6a 04} (ie. without the operand size prefix),
-which is correct since the processor default operand size is assumed to
-be 16 bits in a 16-bit code section.
+opcode bytes @samp{6a 04} (ie. without the operand size prefix), which
+is correct since the processor default operand size is assumed to be 16
+bits in a 16-bit code section.
@node i386-Bugs
@section AT&T Syntax bugs
operands where the source register is @samp{%st} and the destination
register is @samp{%st(i)}.
+@node i386-Arch
+@section Specifying CPU Architecture
+
+@cindex arch directive, i386
+@cindex i386 arch directive
+@cindex arch directive, x86-64
+@cindex x86-64 arch directive
+
+@code{@value{AS}} may be told to assemble for a particular CPU
+architecture with the @code{.arch @var{cpu_type}} directive. This
+directive enables a warning when gas detects an instruction that is not
+supported on the CPU specified. The choices for @var{cpu_type} are:
+
+@multitable @columnfractions .20 .20 .20 .20
+@item @samp{i8086} @tab @samp{i186} @tab @samp{i286} @tab @samp{i386}
+@item @samp{i486} @tab @samp{i586} @tab @samp{i686} @tab @samp{pentium}
+@item @samp{pentiumpro} @tab @samp{pentium4} @tab @samp{k6} @tab @samp{athlon}
+@item @samp{sledgehammer}
+@end multitable
+
+Apart from the warning, there are only two other effects on
+@code{@value{AS}} operation; Firstly, if you specify a CPU other than
+@samp{i486}, then shift by one instructions such as @samp{sarl $1, %eax}
+will automatically use a two byte opcode sequence. The larger three
+byte opcode sequence is used on the 486 (and when no architecture is
+specified) because it executes faster on the 486. Note that you can
+explicitly request the two byte opcode by writing @samp{sarl %eax}.
+Secondly, if you specify @samp{i8086}, @samp{i186}, or @samp{i286},
+@emph{and} @samp{.code16} or @samp{.code16gcc} then byte offset
+conditional jumps will be promoted when necessary to a two instruction
+sequence consisting of a conditional jump of the opposite sense around
+an unconditional jump to the target.
+
+Following the CPU architecture, you may specify @samp{jumps} or
+@samp{nojumps} to control automatic promotion of conditional jumps.
+@samp{jumps} is the default, and enables jump promotion; All external
+jumps will be of the long variety, and file-local jumps will be promoted
+as necessary. (@pxref{i386-Jumps}) @samp{nojumps} leaves external
+conditional jumps as byte offset jumps, and warns about file-local
+conditional jumps that @code{@value{AS}} promotes.
+Unconditional jumps are treated as for @samp{jumps}.
+
+For example
+
+@smallexample
+ .arch i8086,nojumps
+@end smallexample
+
@node i386-Notes
@section Notes
@cindex i386 @code{mul}, @code{imul} instructions
@cindex @code{mul} instruction, i386
@cindex @code{imul} instruction, i386
+@cindex @code{mul} instruction, x86-64
+@cindex @code{imul} instruction, x86-64
There is some trickery concerning the @samp{mul} and @samp{imul}
-instructions that deserves mention. The 16-, 32-, and 64-bit expanding
+instructions that deserves mention. The 16-, 32-, 64- and 128-bit expanding
multiplies (base opcode @samp{0xf6}; extension 4 for @samp{mul} and 5
for @samp{imul}) can be output only in the one operand form. Thus,
@samp{imul %ebx, %eax} does @emph{not} select the expanding multiply;