Links
+* <https://bugs.libre-soc.org/show_bug.cgi?id=915> add overflow to maxmin.
+* <https://bugs.libre-soc.org/show_bug.cgi?id=863> add pseudocode etc.
+* <https://bugs.libre-soc.org/show_bug.cgi?id=234> hardware implementation
+* <https://bugs.libre-soc.org/show_bug.cgi?id=910> mins/maxs zero-option?
+* <https://bugs.libre-soc.org/show_bug.cgi?id=1057> move all int/fp min/max to ls013
* [[vpu]]
-* TODO review https://en.m.wikipedia.org/wiki/Multimedia_Acceleration_eXtensions
+* [[sv/int_fp_mv]]
+* [[openpower/isa/av]] pseudocode
+* [[av_opcodes/analysis]]
+* TODO review HP 1994-6 PA-RISC MAX <https://en.m.wikipedia.org/wiki/Multimedia_Acceleration_eXtensions>
+* <https://en.m.wikipedia.org/wiki/Sum_of_absolute_differences>
+* List of MMX instructions <https://cs.fit.edu/~mmahoney/cse3101/mmx.html>
# Summary
In-advance, the summary of base scalar operations that need to be added is:
-| instruction | pseudocode |
-| ------------ | ------------------------ |
-| average-add. | result = (src1 + src2 + 1) >> 1 |
-| abs-diff | result = abs (src1-src2) |
-| signed min | result = (src1 < src2) ? src1 : src2 use bitmanip |
-| signed max | result = (src1 > src2) ? src1 : src2 use bitmanip |
-| bitwise sel | (a ? b : c) - use bitmanip ternary |
+| instruction | pseudocode |
+| ------------ | ------------------------ |
+| average-add. | result = (src1 + src2 + 1) >> 1 |
+| abs-diff | result = abs (src1-src2) |
+| abs-accumulate| result += abs (src1-src2) |
+| (un)signed min| result = (src1 < src2) ? src1 : src2 [[ls013]] |
+| (un)signed max| result = (src1 > src2) ? src1 : src2 [[ls013]] |
+| bitwise sel | (a ? b : c) - use [[sv/bitmanip]] ternary |
+| int/fp move | covered by REMAP and Pack/Unpack |
-All other capabilities (saturate in particular) are achieved with [[sv/svp64]] modes and swizzle. Note that minmax and ternary are added in bitmanip.
-
-# Audio
-
-The fundamental principle for these instructions is:
-
-* identify the scalar primitive
-* assume that longer runs of scalars will have Simple-V vectorisatin applied
-* assume that "swizzle" may be applied at the (vec2 - SUBVL=2) Vector level,
- (even if that involves a mv.swizxle which may be macro-op fused)
- in order to perform the necessary HI/LO selection normally hard-coded
- into SIMD ISAs.
-
-Thus for example, where OpenPOWER VSX has vpkswss, this would be achieved in SV with simply:
-
-* addition of a scalar ext/clamp instruction
-* 1st op, swizzle-selection vec2 "select X only" from source to dest:
- dest.X = extclamp(src.X)
-* 2nd op, swizzle-select vec2 "select Y only" from source to dest
- dest.Y = extclamp(src.Y)
-
-Macro-op fusion may be used to detect that these two interleave cleanly, overlapping the vec2.X with vec2.Y to produce a single vec2.XY operation.
-
-## Scalar element operations
-
-* clamping / saturation for signed and unsigned. best done similar to FP rounding modes, i.e. with an SPR.
-* average-add. result = (src1 + src2 + 1) >> 1
-* abs-diff: result = (src1 > src2) ? (src1-src2) : (src2-src1)
-* signed min/max
-
-# Video
-
-TODO
-
-* DCT <https://users.cs.cf.ac.uk/Dave.Marshall/Multimedia/node231.html>
-* <https://www.nayuki.io/page/fast-discrete-cosine-transform-algorithms>
-
-# VSX SIMD
-
-Useful parts of VSX, and how they might map.
-
-## vpks[\*][\*]s (vec_pack*)
-
-signed and unsigned, these are N-to-M (N=64/32/16, M=32/16/8) chop/clamp/sign/zero-extend operations. May be implemented by a clamped move to a smaller elwidth.
-
-The other direction, vec_unpack widening ops, may need some way to tell whether to sign-extend or zero-extend.
-
-*scalar extsw/b/h gives one set, mv gives another. src elwidth override and dest elwidth override provide the pack/unpack*
-
-## vavgs\* (vec_avg)
-
-signed and unsigned, 8/16/32: these are all of the form:
-
- result = truncate((a + b + 1) >> 1))
-
-*These do not exist in scalar ISA and would need to be added. Essentially it is a type of post-processing involving the CA bit so could be included in the existing scalar pipeline ALU*
+Implemented at the [[openpower/isa/av]] pseudocode page.
-## vabsdu\* (vec_abs)
-
-unsigned 8/16/32: these are all of the form:
-
- result = (src1 > src2) ? truncate(src1-src2) :
- truncate(src2-src1)
-
-*These do not exist in the scalar ISA and would need to be added*
-
-## vmaxs\* / vmaxu\* (and min)
-
-signed and unsigned, 8/16/32: these are all of the form:
-
- result = (src1 > src2) ? src1 : src2 # max
- result = (src1 < src2) ? src1 : src2 # min
-
-*These do not exist in the scalar INTEGER ISA and would need to be added*
-
-## vmerge operations
-
-Their main point was to work around the odd/even multiplies. SV swizzles and mv.x should handle all cases.
-
-these take two src vectors of various widths and splice them together. the best technique to cover these is a simple straightforward predicated pair of mv operations, inverting the predicate in the second case, or, alternately, to use a pair of vec2 (SUBVL=2) swizzled operations.
-
-in the swizzle case the first instruction would be destvec2.X = srcvec2.X and the second would swizzle-select Y: destvec2.Y = srcvec2.Y. macro-op fusion in both the predicated variant and the swizzle variant would interleave the two into the same SIMD backend ALUs (or macro-op fusion identifies the patterns)
-
-with twin predication the elwidth can be overridden on both src and dest such that either straight scalar mv or extsw/b/h can be used to provide the combinations of coverage needed, with only 2 actual instructions (plus vector prefixing)
-
-See [[sv/mv.vec]] and [[sv/mv.swizzle]]
-
-## Float estimates
-
- vec_expte - float 2^x
- vec_loge - float log2(x)
- vec_re - float 1/x
- vec_rsqrte - float 1/sqrt(x)
-
-The spec says the max relative inaccuracy is 1/4096.
-
-*In conjunction with the FPSPR "accuracy" bit These could be done by assigning meaning to the "sat mode" SVP64 bits in a FP context. 0b00 is IEEE754 FP, 0b01 is 2^12 accuracy for FP32. These can be applied to standard scalar FP ops*
-
-The other alternative is to use the "single precision" FP operations on a 32-bit elwidth override. As explained in [[sv/fcvt]] this halves the precision,
-operating at FP16 accuracy but storing in a FP32 format.
-
-## vec_madd(s) - FMA, multiply-add, optionally saturated
-
- a * b + c
+All other capabilities (saturate in particular) are achieved with [[sv/svp64]] modes and swizzle. Note that minmax and ternary are added in bitmanip.
-*Standard scalar madd*
+# Instructions
-## vec_msum(s) - horizontal gather multiply-add, optionally saturated
+## Average Add
-This should be separated to a horizontal multiply and a horizontal add. How a horizontal operation would work in SV is TBD, how wide is it, etc.
+X-Form
- a.x + a.y + a.z ...
- a.x * a.y * a.z ...
+* avgadd RT,RA,RB (Rc=0)
+* avgadd. RT,RA,RB (Rc=1)
-*This would realistically need to be done with a loop doing a mapreduce sequence. I looked very early on at doing this type of operation and concluded it would be better done with a series of halvings each time, as separate instructions: VL=16 then VL=8 then 4 then 2 and finally one scalar. i.e. not an actual part of SV al all. An OoO multi-issue engine would be more than capable of dealing with the Dependencies.*
+Pseudo-code:
-That has the issue that's it's a massive PITA to code, plus it's slow. Plus there's the "access to non-4-offset regs stalls". Even if there's no ready operation, it should be made easier and faster than a manual mapreduce loop.
+ a <- [0] * (XLEN+1)
+ b <- [0] * (XLEN+1)
+ a[1:XLEN] <- (RA)
+ b[1:XLEN] <- (RB)
+ r <- (a + b + 1)
+ RT <- r[0:XLEN-1]
---
+Special Registers Altered:
-As a mid-solution, 4-element gathers were discussed. 4 elements would also make them useful for pixel packing, not just the general vector gather. This is because OR and ADD are the same operation when bits don't overlap.
+ CR0 (if Rc=1)
- gather-add: d = a.x + a.y + a.z + a.w
- gather-mul: d = a.x * a.y * a.z * a.w
+## Absolute Signed Difference
-But can the SV loop increment the src reg # by 4? Hmm.
+X-Form
-The idea then leads to the opposite operation, a 1-to-4 bit scatter instruction. Like gather, it could be implemented with a normal loop, but it's faster for certain uses.
+* absds RT,RA,RB (Rc=0)
+* absds. RT,RA,RB (Rc=1)
- bit-scatter dest, src, bits
+Pseudo-code:
- bit-scatter rd, rs, 8 # assuming source and dest are 32-bit wide
- rd = (rs >> 0 * 8) & (2^8 - 1)
- rd+1 = (rs >> 1 * 8) & (2^8 - 1)
- rd+2 = (rs >> 2 * 8) & (2^8 - 1)
- rd+3 = (rs >> 3 * 8) & (2^8 - 1)
+ if (RA) < (RB) then RT <- ¬(RA) + (RB) + 1
+ else RT <- ¬(RB) + (RA) + 1
-So at the start you have a RGBA packed pixel in one 32-bit register, at the end you have each channel separated into its own register, in the low bits, and ANDed so only the relevant bits are there.
+Special Registers Altered:
-## vec_mul*
+ CR0 (if Rc=1)
-There should be both a same-width multiply and a widening multiply. Signed and unsigned versions. Optionally saturated.
+## Absolute Unsigned Difference
- u8 * u8 = u8
- u8 * u8 = u16
+X-Form
-For 8,16,32,64, resulting in 8,16,32,64,128.
+* absdu RT,RA,RB (Rc=0)
+* absdu. RT,RA,RB (Rc=1)
-*All of these can be done with SV elwidth overrides, as long as the dest is no greater than 128. SV specifically does not do 128 bit arithmetic. Instead, vec2.X mul-lo followed by vec2.Y mul-hi can be macro-op fused to get at the full 128 bit internal result. Specifying e.g. src elwidth=8 and dest elwidth=16 will give a widening multiply*
+Pseudo-code:
-## vec_rl - rotate left
+ if (RA) <u (RB) then RT <- ¬(RA) + (RB) + 1
+ else RT <- ¬(RB) + (RA) + 1
- (a << x) | (a >> (WIDTH - x))
+Special Registers Altered:
-*Standard scalar rlwinm*
+ CR0 (if Rc=1)
-## vec_sel - bitwise select
+## Absolute Accumulate Unsigned Difference
- (a ? b : c)
+X-Form
-*This does not exist in the scalar ISA and would need to be added*
+* absdacu RT,RA,RB (Rc=0)
+* absdacu. RT,RA,RB (Rc=1)
-Interesting operation: Tim.Forsyth's video on Larrabee they added a logical ternary lookup table op, which can cover this and more. similar to crops 2-2 bit lookup.
+Pseudo-code:
-* <http://0x80.pl/articles/avx512-ternary-functions.html>
-* <https://github.com/WojciechMula/ternary-logic/blob/master/py/show-function.py>
-* [[sv/bitmanip]]
+ if (RA) <u (RB) then r <- ¬(RA) + (RB) + 1
+ else r <- ¬(RB) + (RA) + 1
+ RT <- (RT) + r
+Special Registers Altered:
-## vec_splat - scatter
+ CR0 (if Rc=1)
-Implemented using swizzle/predicate.
+## Absolute Accumulate Signed Difference
-## vec_perm - permute
+X-Form
-Implemented using swizzle, mv.x.
+* absdacs RT,RA,RB (Rc=0)
+* absdacs. RT,RA,RB (Rc=1)
-## vec_*c[tl]z, vec_popcnt - count leading/trailing zeroes, set bits
+Pseudo-code:
-Bit counts.
+ if (RA) < (RB) then r <- ¬(RA) + (RB) + 1
+ else r <- ¬(RB) + (RA) + 1
+ RT <- (RT) + r
- ctz - count trailing zeroes
- clz - count leading zeroes
- popcnt - count set bits
+Special Registers Altered:
-*These all exist in the scalar ISA*
+ CR0 (if Rc=1)
projects / libreriscv.git / blobdiff