-module GP_2LUT(input IN0, IN1, output OUT);
- parameter [3:0] INIT = 0;
- assign OUT = INIT[{IN1, IN0}];
-endmodule
+`timescale 1ns/1ps
-module GP_3LUT(input IN0, IN1, IN2, output OUT);
- parameter [7:0] INIT = 0;
- assign OUT = INIT[{IN2, IN1, IN0}];
-endmodule
-
-module GP_4LUT(input IN0, IN1, IN2, IN3, output OUT);
- parameter [15:0] INIT = 0;
- assign OUT = INIT[{IN3, IN2, IN1, IN0}];
-endmodule
-
-module GP_BANDGAP(output reg OK, output reg VOUT);
- parameter AUTO_PWRDN = 1;
- parameter CHOPPER_EN = 1;
- parameter OUT_DELAY = 100;
-
- //cannot simulate mixed signal IP
-
-endmodule
-
-module GP_COUNT8(input CLK, input wire RST, output reg OUT);
-
- parameter RESET_MODE = "RISING";
-
- parameter COUNT_TO = 8'h1;
- parameter CLKIN_DIVIDE = 1;
-
- //more complex hard IP blocks are not supported for simulation yet
-
- reg[7:0] count = COUNT_TO;
-
- //Combinatorially output whenever we wrap low
- always @(*) begin
- OUT <= (count == 8'h0);
- end
-
- //POR or SYSRST reset value is COUNT_TO. Datasheet is unclear but conversations w/ Silego confirm.
- //Runtime reset value is clearly 0 except in count/FSM cells where it's configurable but we leave at 0 for now.
- //Datasheet seems to indicate that reset is asynchronous, but for now we model as sync due to Yosys issues...
- always @(posedge CLK) begin
-
- count <= count - 1'd1;
-
- if(count == 0)
- count <= COUNT_MAX;
-
- /*
- if((RESET_MODE == "RISING") && RST)
- count <= 0;
- if((RESET_MODE == "FALLING") && !RST)
- count <= 0;
- if((RESET_MODE == "BOTH") && RST)
- count <= 0;
- */
- end
-
-endmodule
-
-module GP_COUNT14(input CLK, input wire RST, output reg OUT);
-
- parameter RESET_MODE = "RISING";
-
- parameter COUNT_TO = 14'h1;
- parameter CLKIN_DIVIDE = 1;
-
- //more complex hard IP blocks are not supported for simulation yet
-
-endmodule
-
-module GP_DFF(input D, CLK, output reg Q);
- parameter [0:0] INIT = 1'bx;
- initial Q = INIT;
- always @(posedge CLK) begin
- Q <= D;
- end
-endmodule
-
-module GP_DFFR(input D, CLK, nRST, output reg Q);
- parameter [0:0] INIT = 1'bx;
- initial Q = INIT;
- always @(posedge CLK, negedge nRST) begin
- if (!nRST)
- Q <= 1'b0;
- else
- Q <= D;
- end
-endmodule
-
-module GP_DFFS(input D, CLK, nSET, output reg Q);
- parameter [0:0] INIT = 1'bx;
- initial Q = INIT;
- always @(posedge CLK, negedge nSET) begin
- if (!nSET)
- Q <= 1'b1;
- else
- Q <= D;
- end
-endmodule
-
-module GP_DFFSR(input D, CLK, nSR, output reg Q);
- parameter [0:0] INIT = 1'bx;
- parameter [0:0] SRMODE = 1'bx;
- initial Q = INIT;
- always @(posedge CLK, negedge nSR) begin
- if (!nSR)
- Q <= SRMODE;
- else
- Q <= D;
- end
-endmodule
-
-module GP_INV(input IN, output OUT);
- assign OUT = ~IN;
-endmodule
-
-module GP_LFOSC(input PWRDN, output reg CLKOUT);
-
- parameter PWRDN_EN = 0;
- parameter AUTO_PWRDN = 0;
- parameter OUT_DIV = 1;
-
- initial CLKOUT = 0;
-
- //auto powerdown not implemented for simulation
- //output dividers not implemented for simulation
-
- always begin
- if(PWRDN)
- CLKOUT = 0;
- else begin
- //half period of 1730 Hz
- #289017;
- CLKOUT = ~CLKOUT;
- end
- end
-
-endmodule
-
-module GP_POR(output reg RST_DONE);
- parameter POR_TIME = 500;
-
- initial begin
- RST_DONE = 0;
-
- if(POR_TIME == 4)
- #4000;
- else if(POR_TIME == 500)
- #500000;
- else begin
- $display("ERROR: bad POR_TIME for GP_POR cell");
- $finish;
- end
-
- RST_DONE = 1;
-
- end
-
-endmodule
-
-module GP_RCOSC(input PWRDN, output reg CLKOUT_PREDIV, output reg CLKOUT_FABRIC);
-
- parameter PWRDN_EN = 0;
- parameter AUTO_PWRDN = 0;
- parameter PRE_DIV = 1;
- parameter FABRIC_DIV = 1;
- parameter OSC_FREQ = "25k";
-
- initial CLKOUT_PREDIV = 0;
- initial CLKOUT_FABRIC = 0;
-
- //output dividers not implemented for simulation
- //auto powerdown not implemented for simulation
-
- always begin
- if(PWRDN) begin
- CLKOUT_PREDIV = 0;
- CLKOUT_FABRIC = 0;
- end
- else begin
-
- if(OSC_FREQ == "25k") begin
- //half period of 25 kHz
- #20000;
- end
-
- else begin
- //half period of 2 MHz
- #250;
- end
-
- CLKOUT_PREDIV = ~CLKOUT_PREDIV;
- CLKOUT_FABRIC = ~CLKOUT_FABRIC;
- end
- end
-
-endmodule
-
-module GP_RINGOSC(input PWRDN, output reg CLKOUT_PREDIV, output reg CLKOUT_FABRIC);
-
- parameter PWRDN_EN = 0;
- parameter AUTO_PWRDN = 0;
- parameter PRE_DIV = 1;
- parameter FABRIC_DIV = 1;
-
- initial CLKOUT_PREDIV = 0;
- initial CLKOUT_FABRIC = 0;
-
- //output dividers not implemented for simulation
- //auto powerdown not implemented for simulation
-
- always begin
- if(PWRDN) begin
- CLKOUT_PREDIV = 0;
- CLKOUT_FABRIC = 0;
- end
- else begin
- //half period of 27 MHz
- #18.518;
- CLKOUT_PREDIV = ~CLKOUT_PREDIV;
- CLKOUT_FABRIC = ~CLKOUT_FABRIC;
- end
- end
-
-endmodule
-
-//keep constraint needed to prevent optimization since we have no outputs
-(* keep *)
-module GP_SYSRESET(input RST);
- parameter RESET_MODE = "RISING";
-
- //cannot simulate whole system reset
-
-endmodule
-
-module GP_VDD(output OUT);
- assign OUT = 1;
-endmodule
-
-module GP_VSS(output OUT);
- assign OUT = 0;
-endmodule
+`include "cells_sim_ams.v"
+`include "cells_sim_digital.v"
+`include "cells_sim_wip.v"