}
}
-void print_nx_status_register(uint32_t status){
- printf("NX Status Register: 0x%08x\n", status);
-}
+void print_nx_status_register(uint64_t status){
+ printf("NX Status Register: 0x%016lx\n", status);
+ if(verbose){
+ printf(" Transparent Mode: %s\n", status & (1 << 0) ? "Yes" : "No" );
+ printf(" Config Target: ");
+ uint8_t config_target = status & (0b111 << 1) >> 1;
+ switch (config_target){
+ case 0b000: printf("SRAM (0b000)\n"); break;
+ case 0b001: printf("EFUSE Normal (0b001)\n"); break;
+ case 0b010: printf("EFUSE Pseudo (0b010)\n"); break;
+ case 0b011: printf("EFUSE Safe (0b011)\n"); break;
+ default: printf("Invalid (%u)\n", config_target); break;
+ }
-void print_status_register(uint32_t status){
- if(connected_device.type == TYPE_ECP5){
- print_ecp5_status_register(status);
- }else if(connected_device.type == TYPE_NX){
- print_nx_status_register(status);
- }
-}
+ printf(" JTAG Active: %s\n", status & (1 << 4) ? "Yes" : "No" );
+ printf(" PWD Protection: %s\n", status & (1 << 5) ? "Yes" : "No" );
+ printf(" OTP: %s\n", status & (1 << 6) ? "Yes" : "No" );
+ printf(" DONE: %s\n", status & (1 << 8) ? "Yes" : "No" );
+ printf(" ISC Enable: %s\n", status & (1 << 9) ? "Yes" : "No" );
+ printf(" Write Enable: %s\n", status & (1 << 10) ? "Writable" : "Not Writable");
+ printf(" Read Enable: %s\n", status & (1 << 11) ? "Readable" : "Not Readable");
+ printf(" Busy Flag: %s\n", status & (1 << 12) ? "Yes" : "No" );
+ printf(" Fail Flag: %s\n", status & (1 << 13) ? "Yes" : "No" );
+ printf(" Decrypt Only: %s\n", status & (1 << 15) ? "Yes" : "No" );
+ printf(" PWD Enable: %s\n", status & (1 << 16) ? "Yes" : "No" );
+ printf(" PWD All: %s\n", status & (1 << 17) ? "Yes" : "No" );
+ printf(" CID EN: %s\n", status & (1 << 18) ? "Yes" : "No" );
+ printf(" Encrypt Preamble: %s\n", status & (1 << 21) ? "Yes" : "No" );
+ printf(" Std Preamble: %s\n", status & (1 << 22) ? "Yes" : "No" );
+ printf(" SPIm Fail 1: %s\n", status & (1 << 23) ? "Yes" : "No" );
+
+ uint8_t bse_error = (status & (0b1111 << 24)) >> 24;
+ switch (bse_error){
+ case 0b0000: printf(" BSE Error Code: No Error (0b000)\n"); break;
+ case 0b0001: printf(" BSE Error Code: ID Error (0b001)\n"); break;
+ case 0b0010: printf(" BSE Error Code: CMD Error - illegal command (0b010)\n"); break;
+ case 0b0011: printf(" BSE Error Code: CRC Error (0b011)\n"); break;
+ case 0b0100: printf(" BSE Error Code: PRMB Error - preamble error (0b100)\n"); break;
+ case 0b0101: printf(" BSE Error Code: ABRT Error - configuration aborted by the user (0b101)\n"); break;
+ case 0b0110: printf(" BSE Error Code: OVFL Error - data overflow error (0b110)\n"); break;
+ case 0b0111: printf(" BSE Error Code: SDM Error - bitstream pass the size of SRAM array (0b111)\n"); break;
+ case 0b1000: printf(" BSE Error Code: Authentication Error (0b1000)\n"); break;
+ case 0b1001: printf(" BSE Error Code: Authentication Setup Error (0b1001)\n"); break;
+ case 0b1010: printf(" BSE Error Code: Bitstream Engine Timeout Error (0b1010) \n"); break;
+ }
+ printf(" Execution Error: %s\n", status & (1 << 28) ? "Yes" : "No" );
+ printf(" ID Error: %s\n", status & (1 << 29) ? "Yes" : "No" );
+ printf(" Invalid Command: %s\n", status & (1 << 30) ? "Yes" : "No" );
+ printf(" WDT Busy: %s\n", status & (1 << 31) ? "Yes" : "No" );
+ printf(" Dry Run DONE: %s\n", status & (1UL << 33) ? "Yes" : "No" );
+
+ uint8_t bse_error1 = (status & (0b1111UL << 34)) >> 34;
+ switch (bse_error1){
+ case 0b0000: printf(" BSE Error 1 Code: (Previous Bitstream) No Error (0b000)\n"); break;
+ case 0b0001: printf(" BSE Error 1 Code: (Previous Bitstream) ID Error (0b001)\n"); break;
+ case 0b0010: printf(" BSE Error 1 Code: (Previous Bitstream) CMD Error - illegal command (0b010)\n"); break;
+ case 0b0011: printf(" BSE Error 1 Code: (Previous Bitstream) CRC Error (0b011)\n"); break;
+ case 0b0100: printf(" BSE Error 1 Code: (Previous Bitstream) PRMB Error - preamble error (0b100)\n"); break;
+ case 0b0101: printf(" BSE Error 1 Code: (Previous Bitstream) ABRT Error - configuration aborted by the user (0b101)\n"); break;
+ case 0b0110: printf(" BSE Error 1 Code: (Previous Bitstream) OVFL Error - data overflow error (0b110)\n"); break;
+ case 0b0111: printf(" BSE Error 1 Code: (Previous Bitstream) SDM Error - bitstream pass the size of SRAM array (0b111)\n"); break;
+ case 0b1000: printf(" BSE Error 1 Code: (Previous Bitstream) Authentication Error (0b1000)\n"); break;
+ case 0b1001: printf(" BSE Error 1 Code: (Previous Bitstream) Authentication Setup Error (0b1001)\n"); break;
+ case 0b1010: printf(" BSE Error 1 Code: (Previous Bitstream) Bitstream Engine Timeout Error (0b1010) \n"); break;
+ }
+
+ printf(" Bypass Mode: %s\n", status & (1UL << 38) ? "Yes" : "No" );
+ printf(" Flow Through Mode: %s\n", status & (1UL << 39) ? "Yes" : "No" );
+ printf(" SFDP Timeout: %s\n", status & (1UL << 42) ? "Yes" : "No" );
+ printf(" Key Destroy Pass: %s\n", status & (1UL << 43) ? "Yes" : "No" );
+ printf(" INITN: %s\n", status & (1UL << 44) ? "Yes" : "No" );
+ printf(" I3C Parity Error 2: %s\n", status & (1UL << 45) ? "Yes" : "No" );
+ printf(" Init Bus ID Error: %s\n", status & (1UL << 46) ? "Yes" : "No" );
+ printf(" I3C Parity Error 1: %s\n", status & (1UL << 47) ? "Yes" : "No" );
+
+ uint8_t auth_mode = (status & (0b11UL << 48)) >> 48;
+ switch (auth_mode){
+ case 0b00: printf(" Authentication Mode: No Auth (0b00)\n"); break;
+ case 0b01: printf(" Authentication Mode: ECDSA (0b01)\n"); break;
+ case 0b10: printf(" Authentication Mode: HMAC (0b10)\n"); break;
+ case 0b11: printf(" Authentication Mode: No Auth (0b11)\n"); break;
+ }
+ printf(" Authentication Done: %s\n", status & (1UL << 50) ? "Yes" : "No" );
+ printf(" Dry Run Authentication Done: %s\n", status & (1UL << 51) ? "Yes" : "No" );
+ printf(" JTAG Locked: %s\n", status & (1UL << 52) ? "Yes" : "No" );
+ printf(" SSPI Locked: %s\n", status & (1UL << 53) ? "Yes" : "No" );
+ printf(" I2C/I3C Locked: %s\n", status & (1UL << 54) ? "Yes" : "No" );
+ printf(" PUB Read Lock: %s\n", status & (1UL << 55) ? "Yes" : "No" );
+ printf(" PUB Write Lock: %s\n", status & (1UL << 56) ? "Yes" : "No" );
+ printf(" FEA Read Lock: %s\n", status & (1UL << 57) ? "Yes" : "No" );
+ printf(" FEA Write Lock: %s\n", status & (1UL << 58) ? "Yes" : "No" );
+ printf(" AES Read Lock: %s\n", status & (1UL << 59) ? "Yes" : "No" );
+ printf(" AES Write Lock: %s\n", status & (1UL << 60) ? "Yes" : "No" );
+ printf(" PWD Read Lock: %s\n", status & (1UL << 61) ? "Yes" : "No" );
+ printf(" PWD Write Lock: %s\n", status & (1UL << 62) ? "Yes" : "No" );
+ printf(" Global Lock: %s\n", status & (1UL << 63) ? "Yes" : "No" );
+ }
+
+}
static void read_status_register(){
- uint8_t data[4] = {LSC_READ_STATUS};
+ uint8_t data[8] = {LSC_READ_STATUS};
jtag_go_to_state(STATE_SHIFT_IR);
jtag_tap_shift(data, data, 8, true);
data[0] = 0;
jtag_go_to_state(STATE_SHIFT_DR);
- jtag_tap_shift(data, data, 32, true);
//jtag_go_to_state(STATE_PAUSE_DR);
-
- uint32_t status = 0;
- /* Format the IDCODE into a 32bit value */
- for(int i = 0; i< 4; i++)
- status = data[i] << 24 | status >> 8;
+ if(connected_device.type == TYPE_ECP5){
+ jtag_tap_shift(data, data, 32, true);
+ uint32_t status = 0;
+
+ /* Format the status into a 32bit value */
+ for(int i = 0; i< 4; i++)
+ status = data[i] << 24 | status >> 8;
+
+ print_ecp5_status_register(status);
+ }else if(connected_device.type == TYPE_NX){
- print_status_register(status);
+ jtag_tap_shift(data, data, 64, true);
+
+ uint64_t status = 0;
+
+ /* Format the status into a 32bit value */
+ for(int i = 0; i< 8; i++)
+ status = (uint64_t)data[i] << 56 | status >> 8;
+
+ print_nx_status_register(status);
+ }
}
if (test_mode)
{
/* Reset ECP5 to release SPI interface */
- ecp_jtag_cmd(ISC_ENABLE);
- ecp_jtag_cmd(ISC_ERASE);
+ ecp_jtag_cmd8(ISC_ENABLE,0);
+ usleep(10000);
+ ecp_jtag_cmd8(ISC_ERASE,0);
+ usleep(10000);
ecp_jtag_cmd(ISC_DISABLE);
/* Put device into SPI bypass mode */
projects / ecpprog.git / commitdiff