nanopi_m1_defconfig: { extends: .defconfig }
nanopi_m1_plus_defconfig: { extends: .defconfig }
nanopi_neo_defconfig: { extends: .defconfig }
+nanopi_r1_defconfig: { extends: .defconfig }
nexbox_a95x_defconfig: { extends: .defconfig }
nitrogen6sx_defconfig: { extends: .defconfig }
nitrogen6x_defconfig: { extends: .defconfig }
F: package/ev3dev-linux-drivers/
N: Davide Viti <zinosat@tiscali.it>
+F: board/friendlyarm/nanopi-r1/
+F: configs/nanopi_r1_defconfig
F: package/flann/
F: package/python-paho-mqtt/
F: package/qhull/
--- /dev/null
+setenv fdt_high ffffffff
+
+setenv bootargs console=ttyS0,115200 earlyprintk root=/dev/mmcblk0p2 rootwait
+
+fatload mmc 0 $kernel_addr_r zImage
+fatload mmc 0 $fdt_addr_r sun8i-h3-nanopi-r1.dtb
+
+bootz $kernel_addr_r - $fdt_addr_r
--- /dev/null
+# Minimal SD card image for the NanoPi M1
+#
+image boot.vfat {
+ vfat {
+ files = {
+ "zImage",
+ "sun8i-h3-nanopi-r1.dtb",
+ "boot.scr"
+ }
+ }
+ size = 10M
+}
+
+image sdcard.img {
+ hdimage {
+ }
+
+ partition u-boot {
+ in-partition-table = "no"
+ image = "u-boot-sunxi-with-spl.bin"
+ offset = 8192
+ size = 1040384 # 1MB - 8192
+ }
+
+ partition boot {
+ partition-type = 0xC
+ bootable = "true"
+ image = "boot.vfat"
+ }
+
+ partition rootfs {
+ partition-type = 0x83
+ image = "rootfs.ext4"
+ size = 512M
+ }
+}
--- /dev/null
+# USB ethernet
+CONFIG_USB_RTL8152=y
--- /dev/null
+/*
+ * Copyright (C) 2019 Igor Pecovnik <igor@armbian.com>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+#include "sun8i-h3-nanopi.dtsi"
+
+/ {
+ model = "FriendlyElec NanoPi-R1";
+ compatible = "friendlyarm,nanopi-r1", "allwinner,sun8i-h3";
+
+ aliases {
+ serial1 = &uart3;
+ ethernet0 = &emac;
+ ethernet1 = &emac;
+ ethernet2 = &sdio_wifi;
+ };
+
+ wifi_pwrseq: wifi_pwrseq {
+ compatible = "mmc-pwrseq-simple";
+ pinctrl-names = "default";
+ reset-gpios = <&r_pio 0 7 GPIO_ACTIVE_LOW>; /* PL7 */
+ };
+
+ reg_gmac_3v3: gmac-3v3 {
+ compatible = "regulator-fixed";
+ regulator-name = "gmac-3v3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ startup-delay-us = <100000>;
+ enable-active-high;
+ gpio = <&pio 3 6 GPIO_ACTIVE_HIGH>;
+ };
+
+ leds {
+ /delete-node/ status;
+ /delete-node/ pwr;
+ led1 {
+ label = "LED1";
+ gpios = <&pio 0 10 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "heartbeat";
+ };
+
+ led2 {
+ label = "LED2";
+ gpios = <&pio 6 11 GPIO_ACTIVE_HIGH>;
+ default-state = "off";
+ linux,default-trigger = "netdev";
+ };
+
+ led3 {
+ label = "LED3";
+ gpios = <&pio 0 9 GPIO_ACTIVE_HIGH>;
+ default-state = "off";
+ linux,default-trigger = "netdev";
+ };
+ };
+
+ r_gpio_keys {
+ compatible = "gpio-keys";
+ input-name = "k1";
+ pinctrl-names = "default";
+ pinctrl-0 = <&sw_r_npi>;
+
+ /delete-node/ k1;
+ reset {
+ label = "reset";
+ linux,code = <BTN_1>;
+ gpios = <&r_pio 0 3 GPIO_ACTIVE_LOW>;
+ };
+ };
+};
+
+&emac {
+ pinctrl-names = "default";
+ pinctrl-0 = <&emac_rgmii_pins>;
+ phy-supply = <®_gmac_3v3>;
+ phy-handle = <&ext_rgmii_phy>;
+ phy-mode = "rgmii";
+
+ status = "okay";
+};
+
+&external_mdio {
+ ext_rgmii_phy: ethernet-phy@1 {
+ compatible = "ethernet-phy-ieee802.3-c22";
+ reg = <7>;
+ };
+};
+
+&mmc1 {
+ vmmc-supply = <®_vcc3v3>;
+ vqmmc-supply = <®_vcc3v3>;
+ mmc-pwrseq = <&wifi_pwrseq>;
+ bus-width = <4>;
+ non-removable;
+ status = "okay";
+
+ sdio_wifi: sdio_wifi@1 {
+ reg = <1>;
+ compatible = "brcm,bcm4329-fmac";
+ interrupt-parent = <&pio>;
+ interrupts = <6 10 IRQ_TYPE_LEVEL_LOW>; /* PG10 / EINT10 */
+ interrupt-names = "host-wake";
+ };
+};
+
+&mmc2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc2_8bit_pins>;
+ vmmc-supply = <®_vcc3v3>;
+ vqmmc-supply = <®_vcc3v3>;
+ bus-width = <8>;
+ non-removable;
+ status = "okay";
+};
+
+&ohci0 {
+ status = "okay";
+};
+
+&ohci1 {
+ status = "okay";
+};
+
+&usb_otg {
+ dr_mode = "peripheral";
+ status = "okay";
+};
+
+&usbphy {
+ status = "okay";
+};
--- /dev/null
+NanoPi R1
+
+Intro
+=====
+
+This default configuration will allow you to start experimenting with the
+buildroot environment for the NanoPi R1. With the current configuration
+it will bring-up the board, and allow access through the serial console.
+
+How to build it
+===============
+
+Configure Buildroot:
+
+ $ make nanopi_r1_defconfig
+
+Compile everything and build the SD card image:
+
+ $ make
+
+How to write the SD card
+========================
+
+Once the build process is finished you will have an image called "sdcard.img"
+in the output/images/ directory.
+
+Copy the bootable "sdcard.img" onto an SD card with "dd":
+
+ $ sudo dd if=output/images/sdcard.img of=/dev/sdX
--- /dev/null
+CONFIG_ARM=y
+CONFIG_ARCH_SUNXI=y
+CONFIG_SPL=y
+CONFIG_MACH_SUN8I_H3=y
+CONFIG_DRAM_CLK=408
+CONFIG_DRAM_ZQ=3881979
+CONFIG_DRAM_ODT_EN=y
+CONFIG_MACPWR="PD6"
+# CONFIG_VIDEO_DE2 is not set
+CONFIG_NR_DRAM_BANKS=1
+# CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
+CONFIG_CONSOLE_MUX=y
+CONFIG_SYS_CLK_FREQ=480000000
+# CONFIG_CMD_FLASH is not set
+# CONFIG_SPL_DOS_PARTITION is not set
+# CONFIG_SPL_EFI_PARTITION is not set
+CONFIG_DEFAULT_DEVICE_TREE="sun8i-h3-nanopi-r1"
+CONFIG_SUN8I_EMAC=y
+CONFIG_USB_EHCI_HCD=y
+CONFIG_USB_OHCI_HCD=y
+CONFIG_SYS_USB_EVENT_POLL_VIA_INT_QUEUE=y
+CONFIG_MMC_SUNXI_SLOT_EXTRA=2
--- /dev/null
+/*
+ * Copyright (C) 2019 Igor Pecovnik <igor@armbian.com>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+#include "sun8i-h3-nanopi.dtsi"
+
+/ {
+ model = "FriendlyARM NanoPi R1";
+ compatible = "friendlyarm,nanopi-neo", "allwinner,sun8i-h3";
+
+ reg_gmac_3v3: gmac-3v3 {
+ compatible = "regulator-fixed";
+ pinctrl-names = "default";
+ regulator-name = "gmac-3v3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ startup-delay-us = <100000>;
+ enable-active-high;
+ gpio = <&pio 3 6 GPIO_ACTIVE_HIGH>;
+ };
+
+};
+
+&ehci0 {
+ status = "okay";
+};
+
+&pio {
+ gmac_power_pin_nanopi: gmac_power_pin@0 {
+ pins = "PD6";
+ function = "gpio_out";
+ };
+};
+
+&ohci0 {
+ status = "okay";
+};
+
+&mmc2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc2_8bit_pins>;
+ vmmc-supply = <®_vcc3v3>;
+ bus-width = <8>;
+ non-removable;
+ cap-mmc-hw-reset;
+ status = "okay";
+};
+
+&emac {
+ pinctrl-names = "default";
+ pinctrl-0 = <&emac_rgmii_pins>;
+ phy-supply = <®_gmac_3v3>;
+ phy-handle = <&ext_rgmii_phy>;
+ phy-mode = "rgmii";
+
+ status = "okay";
+};
+
+&external_mdio {
+ ext_rgmii_phy: ethernet-phy@1 {
+ compatible = "ethernet-phy-ieee802.3-c22";
+ reg = <7>;
+ };
+};
--- /dev/null
+# Architecture
+BR2_arm=y
+BR2_cortex_a7=y
+BR2_ARM_FPU_VFPV4=y
+
+# Linux headers same as kernel, a 5.0 series
+BR2_PACKAGE_HOST_LINUX_HEADERS_CUSTOM_5_0=y
+
+# System configuration
+BR2_TARGET_GENERIC_HOSTNAME="nanopi-r1"
+BR2_TARGET_GENERIC_ISSUE="Welcome to Buildroot for the NanoPi R1"
+
+# Bootloaders
+BR2_TARGET_UBOOT=y
+BR2_TARGET_UBOOT_BUILD_SYSTEM_KCONFIG=y
+BR2_TARGET_UBOOT_CUSTOM_VERSION=y
+BR2_TARGET_UBOOT_CUSTOM_VERSION_VALUE="2019.01"
+BR2_TARGET_UBOOT_BOARD_DEFCONFIG="nanopi_r1"
+BR2_TARGET_UBOOT_NEEDS_DTC=y
+BR2_TARGET_UBOOT_CUSTOM_DTS_PATH="board/friendlyarm/nanopi-r1/uboot/sun8i-h3-nanopi-r1.dts"
+BR2_TARGET_UBOOT_NEEDS_PYLIBFDT=y
+BR2_TARGET_UBOOT_FORMAT_CUSTOM=y
+BR2_TARGET_UBOOT_FORMAT_CUSTOM_NAME="u-boot-sunxi-with-spl.bin"
+BR2_TARGET_UBOOT_USE_CUSTOM_CONFIG=y
+BR2_TARGET_UBOOT_CUSTOM_CONFIG_FILE="board/friendlyarm/nanopi-r1/uboot/nanopi_r1_defconfig"
+
+# Kernel
+BR2_LINUX_KERNEL=y
+BR2_LINUX_KERNEL_CUSTOM_VERSION=y
+BR2_LINUX_KERNEL_CUSTOM_VERSION_VALUE="5.0"
+BR2_LINUX_KERNEL_DEFCONFIG="sunxi"
+BR2_LINUX_KERNEL_CONFIG_FRAGMENT_FILES="board/friendlyarm/nanopi-r1/kernel/linux-extras.config"
+BR2_LINUX_KERNEL_DTS_SUPPORT=y
+BR2_LINUX_KERNEL_CUSTOM_DTS_PATH="board/friendlyarm/nanopi-r1/kernel/sun8i-h3-nanopi-r1.dts"
+BR2_LINUX_KERNEL_INTREE_DTS_NAME="sun8i-h3-nanopi-r1"
+
+# Filesystem
+BR2_TARGET_ROOTFS_EXT2=y
+BR2_TARGET_ROOTFS_EXT2_4=y
+BR2_TARGET_UBOOT_BOOT_SCRIPT=y
+BR2_TARGET_UBOOT_BOOT_SCRIPT_SOURCE="board/friendlyarm/nanopi-r1/boot.cmd"
+BR2_ROOTFS_POST_IMAGE_SCRIPT="support/scripts/genimage.sh"
+BR2_ROOTFS_POST_SCRIPT_ARGS="-c board/friendlyarm/nanopi-r1/genimage.cfg"
+# BR2_TARGET_ROOTFS_TAR is not set
+
+# Additional tools
+BR2_PACKAGE_HOST_DOSFSTOOLS=y
+BR2_PACKAGE_HOST_GENIMAGE=y
+BR2_PACKAGE_HOST_MTOOLS=y
projects / buildroot.git / commitdiff