@table @samp
@item QTDP:@var{n}:@var{addr}:@var{ena}:@var{step}:@var{pass}[:F@var{flen}][:X@var{len},@var{bytes}]@r{[}-@r{]}
+@cindex @samp{QTDP} packet
Create a new tracepoint, number @var{n}, at @var{addr}. If @var{ena}
is @samp{E}, then the tracepoint is enabled; if it is @samp{D}, then
the tracepoint is disabled. @var{step} is the tracepoint's step
mentioned in expressions.
@item QTFrame:@var{n}
+@cindex @samp{QTFrame} packet
Select the @var{n}'th tracepoint frame from the buffer, and use the
register and memory contents recorded there to answer subsequent
request packets from @value{GDBN}.
frame @emph{outside} the given range of addresses (exclusive).
@item qTMinFTPILen
+@cindex @samp{qTMinFTPILen} packet
This packet requests the minimum length of instruction at which a fast
tracepoint (@pxref{Set Tracepoints}) may be placed. For instance, on
the 32-bit x86 architecture, it is possible to use a 4-byte jump, but
@end table
@item QTStart
+@cindex @samp{QTStart} packet
Begin the tracepoint experiment. Begin collecting data from
tracepoint hits in the trace frame buffer. This packet supports the
@samp{qRelocInsn} reply (@pxref{Tracepoint Packets,,Relocate
instruction reply packet}).
@item QTStop
+@cindex @samp{QTStop} packet
End the tracepoint experiment. Stop collecting trace frames.
@item QTEnable:@var{n}:@var{addr}
@anchor{QTEnable}
+@cindex @samp{QTEnable} packet
Enable tracepoint @var{n} at address @var{addr} in a started tracepoint
experiment. If the tracepoint was previously disabled, then collection
of data from it will resume.
@item QTDisable:@var{n}:@var{addr}
@anchor{QTDisable}
+@cindex @samp{QTDisable} packet
Disable tracepoint @var{n} at address @var{addr} in a started tracepoint
experiment. No more data will be collected from the tracepoint unless
@samp{QTEnable:@var{n}:@var{addr}} is subsequently issued.
@item QTinit
+@cindex @samp{QTinit} packet
Clear the table of tracepoints, and empty the trace frame buffer.
@item QTro:@var{start1},@var{end1}:@var{start2},@var{end2}:@dots{}
+@cindex @samp{QTro} packet
Establish the given ranges of memory as ``transparent''. The stub
will answer requests for these ranges from memory's current contents,
if they were not collected as part of the tracepoint hit.
there's no reason for the stub to refuse to provide their contents.
@item QTDisconnected:@var{value}
+@cindex @samp{QTDisconnected} packet
Set the choice to what to do with the tracing run when @value{GDBN}
disconnects from the target. A @var{value} of 1 directs the target to
continue the tracing run, while 0 tells the target to stop tracing if
@value{GDBN} is no longer in the picture.
@item qTStatus
+@cindex @samp{qTStatus} packet
Ask the stub if there is a trace experiment running right now.
The reply has the form:
@end table
@item qTfP
+@cindex @samp{qTfP} packet
@itemx qTsP
+@cindex @samp{qTsP} packet
These packets request data about tracepoints that are being used by
the target. @value{GDBN} sends @code{qTfP} to get the first piece
of data, and multiple @code{qTsP} to get additional pieces. Replies
that define tracepoints. (FIXME add detailed syntax)
@item qTfV
+@cindex @samp{qTfV} packet
@itemx qTsV
+@cindex @samp{qTsV} packet
These packets request data about trace state variables that are on the
target. @value{GDBN} sends @code{qTfV} to get the first vari of data,
and multiple @code{qTsV} to get additional variables. Replies to
@itemx qTsSTM
@anchor{qTfSTM}
@anchor{qTsSTM}
+@cindex @samp{qTfSTM} packet
+@cindex @samp{qTsSTM} packet
These packets request data about static tracepoint markers that exist
in the target program. @value{GDBN} sends @code{qTfSTM} to get the
first piece of data, and multiple @code{qTsSTM} to get additional
@item qTSTMat:@var{address}
@anchor{qTSTMat}
+@cindex @samp{qTSTMat} packet
This packets requests data about static tracepoint markers in the
target program at @var{address}. Replies to this packet follow the
syntax of the @samp{qTfSTM} and @code{qTsSTM} packets that list static
tracepoint markers.
@item QTSave:@var{filename}
+@cindex @samp{QTSave} packet
This packet directs the target to save trace data to the file name
@var{filename} in the target's filesystem. @var{filename} is encoded
as a hex string; the interpretation of the file name (relative vs
absolute, wild cards, etc) is up to the target.
@item qTBuffer:@var{offset},@var{len}
+@cindex @samp{qTBuffer} packet
Return up to @var{len} bytes of the current contents of trace buffer,
starting at @var{offset}. The trace buffer is treated as if it were
a contiguous collection of traceframes, as per the trace file format.
@var{value} is 1, or a linear buffer if the value is 0.
@item QTNotes:@r{[}@var{type}:@var{text}@r{]}@r{[};@var{type}:@var{text}@r{]}@dots{}
+@cindex @samp{QTNotes} packet
This packet adds optional textual notes to the trace run. Allowable
types include @code{user}, @code{notes}, and @code{tstop}, the
@var{text} fields are arbitrary strings, hex-encoded.
projects / binutils-gdb.git / commitdiff