From: Baruch Siach Date: Sun, 16 Jun 2019 08:18:47 +0000 (+0300) Subject: configs/solidrun_clearfog_gt_8k: new defconfig X-Git-Url: https://git.libre-soc.org/?a=commitdiff_plain;h=0de91e572569fc450f74839b1bd3683aed16c196;p=buildroot.git configs/solidrun_clearfog_gt_8k: new defconfig Add support for the SolidRun Armada 8040 based Clearfog GT-8K. This board has the same processor as the Macchiatobin, so we can reuse the Macchiatobin U-Boot and image definitions. The kernel fragment enables drivers that are necessary to make networking ports work (SFP, Ethernet port, and Ethernet switch). Cc: Jan Kundrát Signed-off-by: Baruch Siach Signed-off-by: Thomas Petazzoni --- diff --git a/.gitlab-ci.yml b/.gitlab-ci.yml index 087bfa7602..9cdb5f2b89 100644 --- a/.gitlab-ci.yml +++ b/.gitlab-ci.yml @@ -300,6 +300,7 @@ snps_archs38_hsdk_defconfig: { extends: .defconfig } snps_archs38_vdk_defconfig: { extends: .defconfig } socrates_cyclone5_defconfig: { extends: .defconfig } solidrun_clearfog_defconfig: { extends: .defconfig } +solidrun_clearfog_gt_8k_defconfig: { extends: .defconfig } solidrun_macchiatobin_mainline_defconfig: { extends: .defconfig } solidrun_macchiatobin_marvell_defconfig: { extends: .defconfig } stm32f429_disco_defconfig: { extends: .defconfig } diff --git a/DEVELOPERS b/DEVELOPERS index 62aacc1fd0..9d806db6f7 100644 --- a/DEVELOPERS +++ b/DEVELOPERS @@ -254,6 +254,8 @@ F: package/pulseview/ F: package/sigrok-cli/ N: Baruch Siach +F: board/solidrun/clearfog_gt_8k/ +F: configs/solidrun_clearfog_gt_8k_defconfig F: package/18xx-ti-utils/ F: package/daemon/ F: package/dropbear/ diff --git a/board/solidrun/clearfog_gt_8k/extlinux.conf b/board/solidrun/clearfog_gt_8k/extlinux.conf new file mode 100644 index 0000000000..aae0c0d5fb --- /dev/null +++ b/board/solidrun/clearfog_gt_8k/extlinux.conf @@ -0,0 +1,4 @@ +label Clearfog GT-8K Linux + kernel /boot/Image + devicetree /boot/armada-8040-clearfog-gt-8k.dtb + append console=ttyS0,115200n8 root=/dev/mmcblk1p1 rootwait diff --git a/board/solidrun/clearfog_gt_8k/genimage.cfg b/board/solidrun/clearfog_gt_8k/genimage.cfg new file mode 120000 index 0000000000..0cc2754ff6 --- /dev/null +++ b/board/solidrun/clearfog_gt_8k/genimage.cfg @@ -0,0 +1 @@ +../macchiatobin/genimage.cfg \ No newline at end of file diff --git a/board/solidrun/clearfog_gt_8k/linux-extras.config b/board/solidrun/clearfog_gt_8k/linux-extras.config new file mode 100644 index 0000000000..bce2a2e9d2 --- /dev/null +++ b/board/solidrun/clearfog_gt_8k/linux-extras.config @@ -0,0 +1,4 @@ +CONFIG_MARVELL_PHY=y +CONFIG_SFP=y +CONFIG_NET_DSA=y +CONFIG_NET_DSA_MV88E6XXX=y diff --git a/board/solidrun/clearfog_gt_8k/post-build-mainline.sh b/board/solidrun/clearfog_gt_8k/post-build-mainline.sh new file mode 120000 index 0000000000..a8c9a52437 --- /dev/null +++ b/board/solidrun/clearfog_gt_8k/post-build-mainline.sh @@ -0,0 +1 @@ +../macchiatobin/post-build-mainline.sh \ No newline at end of file diff --git a/board/solidrun/clearfog_gt_8k/readme.txt b/board/solidrun/clearfog_gt_8k/readme.txt new file mode 100644 index 0000000000..1648ffa38d --- /dev/null +++ b/board/solidrun/clearfog_gt_8k/readme.txt @@ -0,0 +1,61 @@ +Intro +===== + +The default configuration described below will allow you to start +experimenting with the buildroot environment for the SolidRun Clearfog GT-8K +based on the Marvell Armada 8040 SoC. + +This default configuration will bring up the board and allow shell command +line access through the serial console. + +How to build +============ + + $ make solidrun_clearfog_gt_8k_defconfig + $ make + +How to write the SD card +======================== + +Once the build process is finished you will have an image file named +"sdcard.img" in the output/images/ directory. + +Copy the bootable "sdcard.img" onto an SD card with "dd": + + $ sudo dd if=output/images/sdcard.img of=/dev/sdX bs=1M conv=fsync + +How to boot the board +===================== + +The Clearfog GT-8K can be setup to load the bootloader from different sources +including eMMC, SPI flash, and SD-card. + +To select boot from SD-card the DIP switches in SW6 (at the bottom of the +board) should be configured as follows: + + SW6: 11010 + +Insert the micro SDcard in the Cleargfog GT-8K and power it up. + +Serial console +============== + +The serial console is accessible at the J27 pins header (TTL UART) with the +following pinout (pin #1 is marked with triangle on the PCB): + + pin #1: Ground + pin #2: Armada 8040 Rx + pin #3: Armada 8040 Tx + +Enable the switch (yellow) Ethernet ports +========================================= + +To enable the Clearfog GT-8K internal switch port make sure to load the +'mv88e6xxx' kernel module, and up the switch up-link port (eth2 by default): + + modprobe mv88e6xxx + ifconfig eth2 up + +Then you can configure each switch port separately. These port are named +'lan1' to 'lan4' by default. 'lan1' is closest to the USB port, while 'lan4' +is closest to the blue Ethernet port. diff --git a/board/solidrun/clearfog_gt_8k/uboot-fragment.config b/board/solidrun/clearfog_gt_8k/uboot-fragment.config new file mode 120000 index 0000000000..996c4aa6b6 --- /dev/null +++ b/board/solidrun/clearfog_gt_8k/uboot-fragment.config @@ -0,0 +1 @@ +../macchiatobin/uboot-fragment.config \ No newline at end of file diff --git a/configs/solidrun_clearfog_gt_8k_defconfig b/configs/solidrun_clearfog_gt_8k_defconfig new file mode 100644 index 0000000000..a44038e663 --- /dev/null +++ b/configs/solidrun_clearfog_gt_8k_defconfig @@ -0,0 +1,46 @@ +BR2_aarch64=y +BR2_PACKAGE_HOST_LINUX_HEADERS_CUSTOM_5_1=y +BR2_TARGET_GENERIC_HOSTNAME="clearfog-gt-8k" +BR2_TARGET_GENERIC_ISSUE="Welcome to Buildroot for SolidRun Clearfog GT-8K" + +# Firmware +BR2_TARGET_ARM_TRUSTED_FIRMWARE=y +BR2_TARGET_ARM_TRUSTED_FIRMWARE_CUSTOM_GIT=y +BR2_TARGET_ARM_TRUSTED_FIRMWARE_CUSTOM_REPO_URL="https://github.com/MarvellEmbeddedProcessors/atf-marvell.git" +# This commit corresponds to release armada-18.09.4 +BR2_TARGET_ARM_TRUSTED_FIRMWARE_CUSTOM_REPO_VERSION="711ecd32afe465b38052b5ba374c825b158eea18" +BR2_TARGET_ARM_TRUSTED_FIRMWARE_PLATFORM="a80x0_mcbin" +BR2_TARGET_ARM_TRUSTED_FIRMWARE_FIP=y +BR2_TARGET_ARM_TRUSTED_FIRMWARE_UBOOT_AS_BL33=y +BR2_TARGET_ARM_TRUSTED_FIRMWARE_ADDITIONAL_VARIABLES="USE_COHERENT_MEM=0" +BR2_TARGET_BINARIES_MARVELL=y +BR2_TARGET_BINARIES_MARVELL_8040=y +BR2_TARGET_MV_DDR_MARVELL=y + +# U-Boot +BR2_TARGET_UBOOT=y +BR2_TARGET_UBOOT_CUSTOM_VERSION=y +BR2_TARGET_UBOOT_CUSTOM_VERSION_VALUE="2019.04" +BR2_TARGET_UBOOT_BUILD_SYSTEM_KCONFIG=y +BR2_TARGET_UBOOT_BOARD_DEFCONFIG="clearfog_gt_8k" +BR2_TARGET_UBOOT_CONFIG_FRAGMENT_FILES="board/solidrun/clearfog_gt_8k/uboot-fragment.config" + +# Kernel +BR2_LINUX_KERNEL=y +BR2_LINUX_KERNEL_CUSTOM_VERSION=y +BR2_LINUX_KERNEL_CUSTOM_VERSION_VALUE="5.1.9" +BR2_LINUX_KERNEL_USE_ARCH_DEFAULT_CONFIG=y +BR2_LINUX_KERNEL_DTS_SUPPORT=y +BR2_LINUX_KERNEL_CONFIG_FRAGMENT_FILES="board/solidrun/clearfog_gt_8k/linux-extras.config" +BR2_LINUX_KERNEL_INTREE_DTS_NAME="marvell/armada-8040-clearfog-gt-8k" +BR2_LINUX_KERNEL_INSTALL_TARGET=y +BR2_LINUX_KERNEL_NEEDS_HOST_OPENSSL=y + +# rootfs +BR2_TARGET_ROOTFS_EXT2=y +BR2_TARGET_ROOTFS_EXT2_4=y +BR2_PACKAGE_HOST_GENIMAGE=y +BR2_ROOTFS_DEVICE_CREATION_DYNAMIC_MDEV=y +BR2_ROOTFS_POST_IMAGE_SCRIPT="support/scripts/genimage.sh" +BR2_ROOTFS_POST_BUILD_SCRIPT="board/solidrun/clearfog_gt_8k/post-build-mainline.sh" +BR2_ROOTFS_POST_SCRIPT_ARGS="-c board/solidrun/clearfog_gt_8k/genimage.cfg"