From: Eli Zaretskii <eliz@gnu.org>
Date: Tue, 9 May 2000 08:24:34 +0000 (+0000)
Subject: 	* gdb.texinfo: Proofreading changes from Brian Youmans.
X-Git-Url: https://git.libre-soc.org/?a=commitdiff_plain;h=598ca718d00001789f64d2669c56f87acea2b3ca;p=binutils-gdb.git

	* gdb.texinfo: Proofreading changes from Brian Youmans.
---

diff --git a/gdb/doc/ChangeLog b/gdb/doc/ChangeLog
index 0ca86117549..98bffdec525 100644
--- a/gdb/doc/ChangeLog
+++ b/gdb/doc/ChangeLog
@@ -1,3 +1,7 @@
+2000-05-09  Eli Zaretskii  <eliz@is.elta.co.il>
+
+	* gdb.texinfo: Proofreading changes from Brian Youmans.
+
 2000-05-01  Nick Duffek  <nsd@cygnus.com>
 
 	* gdb.texinfo (Command Files): Mention -x, use @enumerate for
diff --git a/gdb/doc/gdb.texinfo b/gdb/doc/gdb.texinfo
index 2f466260fce..daba4a381aa 100644
--- a/gdb/doc/gdb.texinfo
+++ b/gdb/doc/gdb.texinfo
@@ -8754,7 +8754,7 @@ void (*exceptionHook)() = 0;
 
 @noindent
 but if before calling @code{set_debug_traps}, you set it to point to a
-function in your program; that function is called when
+function in your program, that function is called when
 @code{@value{GDBN}} continues after stopping on a trap (for example, bus
 error).  The function indicated by @code{exceptionHook} is called with
 one parameter: an @code{int} which is the exception number.
@@ -8928,7 +8928,7 @@ So:
 @noindent
 means the same as "0000".
 
-The error response, returned for some packets includes a two character
+The error response returned for some packets includes a two character
 error number.  That number is not well defined.
 
 For any @var{command} not supported by the stub, an empty response
@@ -8942,7 +8942,7 @@ optional.
 
 Below is a complete list of all currently defined @var{command}s and
 their corresponding response @var{data}:
-
+@page
 @multitable @columnfractions .30 .30 .40
 @item Packet
 @tab Request
@@ -8952,7 +8952,7 @@ their corresponding response @var{data}:
 @tab @code{!}
 @tab
 Use the extended remote protocol.  Sticky---only needs to be set once.
-The extended remote protocol support the @samp{R} packet.
+The extended remote protocol supports the @samp{R} packet.
 @item
 @tab reply @samp{}
 @tab
@@ -8977,6 +8977,9 @@ and continue.
 @item set program arguments @strong{(reserved)}
 @tab @code{A}@var{arglen}@code{,}@var{argnum}@code{,}@var{arg}@code{,...}
 @tab
+@item
+@tab
+@tab
 Initialized @samp{argv[]} array passed into program. @var{arglen}
 specifies the number of bytes in the hex encoded byte stream @var{arg}.
 See @file{gdbserver} for more details.
@@ -9023,7 +9026,7 @@ Continue with signal @var{sig} (hex signal number).  If
 @tab reply
 @tab see below
 
-@item toggle debug @emph{(deprecated)}
+@item toggle debug @strong{(deprecated)}
 @tab @code{d}
 @tab
 toggle debug flag.
@@ -9036,7 +9039,7 @@ Detach @value{GDBN} from the remote system.  Sent to the remote target before
 @item
 @tab reply @emph{no response}
 @tab
-@value{GDBN} does not check for any response after sending this packet
+@value{GDBN} does not check for any response after sending this packet.
 
 @item reserved
 @tab @code{e}
@@ -9219,7 +9222,7 @@ digits for each byte in the register (target byte order).
 @item general query
 @tab @code{q}@var{query}
 @tab
-Request info about @var{query}.  In general @value{GDBN} @var{query}'s
+Request info about @var{query}.  In general @value{GDBN} queries
 have a leading upper case letter.  Custom vendor queries should use a
 company prefix (in lower case) ex: @samp{qfsf.var}.  @var{query} may
 optionally be followed by a @samp{,} or @samp{;} separated list.  Stubs
@@ -9240,7 +9243,7 @@ must ensure that they match the full @var{query} name.
 Set value of @var{var} to @var{val}.  See @samp{q} for a discussing of
 naming conventions.
 
-@item reset @emph{(deprecated)}
+@item reset @strong{(deprecated)}
 @tab @code{r}
 @tab
 Reset the entire system.
@@ -9534,6 +9537,9 @@ offset to the @code{Bss} section.}
 @item thread info request
 @tab @code{q}@code{P}@var{mode}@var{threadid}
 @tab
+@item
+@tab
+@tab
 Returns information on @var{threadid}.  Where: @var{mode} is a hex
 encoded 32 bit mode; @var{threadid} is a hex encoded 64 bit thread ID.
 @item
@@ -9544,6 +9550,9 @@ See @code{remote.c:remote_unpack_thread_info_response()}.
 @item remote command
 @tab @code{q}@code{Rcmd,}@var{COMMAND}
 @tab
+@item
+@tab
+@tab
 @var{COMMAND} (hex encoded) is passed to the local interpreter for
 execution.  Invalid commands should be reported using the output string.
 Before the final result packet, the target may also respond with a