From: Ian Lance Taylor <ian@airs.com>
Date: Sat, 2 Dec 1995 06:17:46 +0000 (+0000)
Subject: 	* ld-srec/srec.exp: Don't use [] in setup_xfail expressions.
X-Git-Url: https://git.libre-soc.org/?a=commitdiff_plain;h=6ceb5612872d412aca921865f02c5b18498ec0f1;p=binutils-gdb.git

	* ld-srec/srec.exp: Don't use [] in setup_xfail expressions.
---

diff --git a/ld/testsuite/ChangeLog b/ld/testsuite/ChangeLog
index a39fd7e078d..be6ab99e5d5 100644
--- a/ld/testsuite/ChangeLog
+++ b/ld/testsuite/ChangeLog
@@ -1,3 +1,7 @@
+Sat Dec  2 01:20:31 1995  Ian Lance Taylor  <ian@cygnus.com>
+
+	* ld-srec/srec.exp: Don't use [] in setup_xfail expressions.
+
 Fri Dec  1 13:18:18 1995  Ian Lance Taylor  <ian@cygnus.com>
 
 	* ld-srec/srec.exp: Add setup_xfails for MIPS ELF targets.
diff --git a/ld/testsuite/ld-srec/srec.exp b/ld/testsuite/ld-srec/srec.exp
index 9583d3f4028..4241c616f19 100644
--- a/ld/testsuite/ld-srec/srec.exp
+++ b/ld/testsuite/ld-srec/srec.exp
@@ -276,12 +276,12 @@ if { ![ld_compile $CC $srcdir/$subdir/sr1.c tmpdir/sr1.o] \
 
 # The i386-aout target is confused: the linker does not put the
 # sections where objdump finds them.  I don't know which is wrong.
-setup_xfail "i\[345\]86-*-aout*"
+setup_xfail "i*86-*-aout*"
 
 # These tests fail on the MIPS ELF target because the GP value in the
 # .reginfo section is not updated when the S-record version is written
 # out.
-setup_xfail "mips*-*-elf*" "mips*-*-irix\[56\]*"
+setup_xfail "mips*-*-elf*" "mips*-*-irix5*" "mips*-*-irix6*"
 
 run_srec_test $test1 "tmpdir/sr1.o tmpdir/sr2.o"
 
@@ -300,14 +300,14 @@ if ![ld_compile "$CXX $CXXFLAGS -fgnu-linker" $srcdir/$subdir/sr3.cc tmpdir/sr3.
 }
 
 # See above.
-setup_xfail "i\[345\]86-*-aout*"
-setup_xfail "mips*-*-elf*" "mips*-*-irix\[56\]*"
+setup_xfail "i*86-*-aout*"
+setup_xfail "mips*-*-elf*" "mips*-*-irix5*" "mips*-*-irix6*"
 
 # The i960 COFF targets fail this test because the i960 defaults to
 # little endian, while the srec target is big endian.  When the number
 # of entries in the constructor table is written out, the linker uses
 # the output BFD.  This seems correct, but it generates the wrong
 # result.  I don't know how to fix this.
-setup_xfail "i960*-*-coff*" "i960*-*-vxworks5.\[123456789\]*"
+setup_xfail "i960*-*-coff*" "i960*-*-vxworks5.1*"
 
 run_srec_test $test2 "tmpdir/sr3.o"