From: Thomas Petazzoni Date: Tue, 4 May 2021 20:51:34 +0000 (+0200) Subject: configs/beaglev_defconfig: new defconfig X-Git-Url: https://git.libre-soc.org/?a=commitdiff_plain;h=839f00a81150a1dddf52a5ec211f8beb9e46f266;p=buildroot.git configs/beaglev_defconfig: new defconfig This commit introduces support for the RISC-V based BeagleV platform, which uses a Starfive JH7100. Signed-off-by: Thomas Petazzoni Reviewed-by: Alistair Francis [yann.morin.1998@free.fr: use: eval $(make printvars)] Signed-off-by: Yann E. MORIN --- diff --git a/DEVELOPERS b/DEVELOPERS index 235828241e..c5f9f36578 100644 --- a/DEVELOPERS +++ b/DEVELOPERS @@ -2602,10 +2602,12 @@ F: package/xorcurses/ N: Thomas Petazzoni F: arch/Config.in.arm +F: board/beaglev/ F: board/stmicroelectronics/stm32mp157c-dk2/ F: boot/boot-wrapper-aarch64/ F: boot/grub2/ F: boot/gummiboot/ +F: configs/beaglev_defconfig F: configs/stm32mp157c_dk2_defconfig F: package/android-tools/ F: package/b43-firmware/ diff --git a/board/beaglev/extlinux.conf b/board/beaglev/extlinux.conf new file mode 100644 index 0000000000..c5444d094c --- /dev/null +++ b/board/beaglev/extlinux.conf @@ -0,0 +1,4 @@ +label linux + kernel /boot/Image + devicetree /boot/starfive_vic7100_beagle_v.dtb + append console=ttyS0,115200 earlyprintk root=PARTUUID=0fef845a-c6e1-45bc-82f7-002fa720f958 rootwait diff --git a/board/beaglev/genimage.cfg b/board/beaglev/genimage.cfg new file mode 100644 index 0000000000..f38bb7f86c --- /dev/null +++ b/board/beaglev/genimage.cfg @@ -0,0 +1,12 @@ +image sdcard.img { + hdimage { + gpt = true + } + + partition rootfs { + partition-type-uuid = 72ec70a6-cf74-40e6-bd49-4bda08e8f224 + partition-uuid = 0fef845a-c6e1-45bc-82f7-002fa720f958 + bootable = "true" + image = "rootfs.ext4" + } +} diff --git a/board/beaglev/patches/uboot/0001-include-configs-starfive-vic7100-adjust-fdt_addr_r.patch b/board/beaglev/patches/uboot/0001-include-configs-starfive-vic7100-adjust-fdt_addr_r.patch new file mode 100644 index 0000000000..74d70f2721 --- /dev/null +++ b/board/beaglev/patches/uboot/0001-include-configs-starfive-vic7100-adjust-fdt_addr_r.patch @@ -0,0 +1,39 @@ +From 2c4c813940c577590f3352cef0c49a8def17905d Mon Sep 17 00:00:00 2001 +From: Thomas Petazzoni +Date: Wed, 28 Apr 2021 22:58:45 +0200 +Subject: [PATCH] include/configs/starfive-vic7100: adjust fdt_addr_r + +The default fdt_addr_r of 0x88000000 doesn't work, the kernel never +boots. Using 0x90000000 works fine. + +Since it would overlap with the kernel_comp_addr_r area, this one is +moved 16 MB further, at 0x91000000. + +Signed-off-by: Thomas Petazzoni +--- + include/configs/starfive-vic7100.h | 4 ++-- + 1 file changed, 2 insertions(+), 2 deletions(-) + +diff --git a/include/configs/starfive-vic7100.h b/include/configs/starfive-vic7100.h +index 8c5915a73c..7150a23873 100644 +--- a/include/configs/starfive-vic7100.h ++++ b/include/configs/starfive-vic7100.h +@@ -111,13 +111,13 @@ + "fdt_high=0xffffffffffffffff\0" \ + "initrd_high=0xffffffffffffffff\0" \ + "kernel_addr_r=0x84000000\0" \ +- "fdt_addr_r=0x88000000\0" \ ++ "fdt_addr_r=0x90000000\0" \ + "scriptaddr=0x88100000\0" \ + "script_offset_f=0x1fff000\0" \ + "script_size_f=0x1000\0" \ + "pxefile_addr_r=0x88200000\0" \ + "ramdisk_addr_r=0x88300000\0" \ +- "kernel_comp_addr_r=0x90000000\0" \ ++ "kernel_comp_addr_r=0x91000000\0" \ + "kernel_comp_size=0x10000000\0" \ + "type_guid_gpt_loader1=" TYPE_GUID_LOADER1 "\0" \ + "type_guid_gpt_loader2=" TYPE_GUID_LOADER2 "\0" \ +-- +2.30.2 + diff --git a/board/beaglev/post-build.sh b/board/beaglev/post-build.sh new file mode 100755 index 0000000000..b19b9bf6d0 --- /dev/null +++ b/board/beaglev/post-build.sh @@ -0,0 +1,17 @@ +#!/bin/sh +BOARD_DIR=$(dirname $0) + +# The DTB to use is provided within the U-Boot source tree, so we grab +# it from there, and install it to TARGET_DIR/boot/. +eval $(make -C ${CONFIG_DIR} --no-print-directory QUOTED_VARS=YES VARS=UBOOT_DIR printvars) +install -D -m0644 ${UBOOT_DIR}/arch/riscv/dts/starfive_vic7100_beagle_v.dtb \ + ${TARGET_DIR}/boot/starfive_vic7100_beagle_v.dtb + +# Bring the extlinux.conf file in. +install -D -m 0644 ${BOARD_DIR}/extlinux.conf \ + ${TARGET_DIR}/boot/extlinux/extlinux.conf + +# To be reflashed through Xmodem, the bootloader needs to be prepended +# with a 4-byte header that contains the total size of the file. +perl -e 'print pack("l", (stat @ARGV[0])[7])' ${BINARIES_DIR}/fw_payload.bin > ${BINARIES_DIR}/fw_payload.bin.out +cat ${BINARIES_DIR}/fw_payload.bin >> ${BINARIES_DIR}/fw_payload.bin.out diff --git a/board/beaglev/readme.txt b/board/beaglev/readme.txt new file mode 100644 index 0000000000..d8511d3fd1 --- /dev/null +++ b/board/beaglev/readme.txt @@ -0,0 +1,88 @@ +BeagleV +======= + +BeagleV is a low-cost RISC-V 64-bit based platform, powered by a +Starfive JH7100 processor. The current defconfig in Buildroot has been +tested with the JH7100 chip used on the beta version of the BeagleV +board. + +How to build +============ + +$ make beaglev_defconfig +$ make + +Build results +============= + +After building, output/images contains: + ++ Image ++ fw_payload.bin ++ fw_payload.bin.out ++ fw_payload.elf ++ rootfs.ext2 ++ rootfs.ext4 ++ sdcard.img ++ u-boot.bin + +The two important files are: + + - fw_payload.bin.out, which is the bootloader image, containing + both OpenSBI and U-Boot. + + - sdcard.img, the SD card image, which contains the root filesystem, + kernel image and Device Tree. + +Flashing the SD card image +========================== + +$ sudo dd if=output/images/sdcard.img of=/dev/sdX + +Preparing the board +=================== + +Connect the Beagle-V fan to the 5V supply (pin 2 or 4 of the GPIO +connector) and GND (pin 6 of the GPIO connector). + +Connect a TTL UART cable to pin 8 (TX), 10 (RX) and 14 (GND). + +Insert your SD card. + +Power-up the board using an USB-C cable. + +Flashing the bootloader +======================= + +The bootloader pre-flashed on the Beagle-V has a non-working +fdt_addr_r environment variable value, so it won't work +as-is. Reflashing the bootloader with the bootloader image produced by +Buildroot is necessary. + +When the board starts up, a pre-loader shows a count down of 2 +seconds, interrupt by pressing any key. You should reach a menu like +this: + +--------8<---------- + +bootloader version:210209-4547a8d +ddr 0x00000000, 1M test +ddr 0x00100000, 2M test +DDR clk 2133M,Version: 210302-5aea32f +0 +*************************************************** +*************** FLASH PROGRAMMING ***************** +*************************************************** + +0:update uboot +1:quit +select the function: + +--------8<---------- + +Press 0 and Enter. You will now see "C" characters being +displayed. Ask your serial port communication program to send +fw_payload.bin.out using the Xmodem protocol. + +After reflashing is complete, restart the board, it will automatically +start the system from the SD card, and reach the login prompt. diff --git a/configs/beaglev_defconfig b/configs/beaglev_defconfig new file mode 100644 index 0000000000..e94c4ab639 --- /dev/null +++ b/configs/beaglev_defconfig @@ -0,0 +1,35 @@ +BR2_riscv=y +BR2_riscv_custom=y +BR2_RISCV_ISA_CUSTOM_RVM=y +BR2_RISCV_ISA_CUSTOM_RVF=y +BR2_RISCV_ISA_CUSTOM_RVD=y +BR2_RISCV_ISA_CUSTOM_RVC=y +BR2_GLOBAL_PATCH_DIR="board/beaglev/patches/" +BR2_PACKAGE_HOST_LINUX_HEADERS_CUSTOM_5_10=y +BR2_ROOTFS_POST_BUILD_SCRIPT="board/beaglev/post-build.sh" +BR2_ROOTFS_POST_IMAGE_SCRIPT="support/scripts/genimage.sh" +BR2_ROOTFS_POST_SCRIPT_ARGS="-c board/beaglev/genimage.cfg" +BR2_LINUX_KERNEL=y +BR2_LINUX_KERNEL_CUSTOM_TARBALL=y +# HEAD of the Fedora branch +BR2_LINUX_KERNEL_CUSTOM_TARBALL_LOCATION="$(call github,starfive-tech,linux,710cf052d6abda73584481d920b4b6befc7240ea)/linux-710cf052d6abda73584481d920b4b6befc7240ea.tar.gz" +BR2_LINUX_KERNEL_DEFCONFIG="starfive_vic7100_evb_sd_net" +BR2_LINUX_KERNEL_INSTALL_TARGET=y +BR2_TARGET_ROOTFS_EXT2=y +BR2_TARGET_ROOTFS_EXT2_4=y +# BR2_TARGET_ROOTFS_TAR is not set +BR2_TARGET_OPENSBI=y +BR2_TARGET_OPENSBI_CUSTOM_TARBALL=y +# HEAD of the Fedora branch +BR2_TARGET_OPENSBI_CUSTOM_TARBALL_LOCATION="$(call github,starfive-tech,opensbi,2524b0ecd8684b42bc7a4c69794f40f11cbbe2a5)/opensbi-2524b0ecd8684b42bc7a4c69794f40f11cbbe2a5.tar.gz" +BR2_TARGET_OPENSBI_PLAT="starfive/vic7100" +# BR2_TARGET_OPENSBI_INSTALL_DYNAMIC_IMG is not set +# BR2_TARGET_OPENSBI_INSTALL_JUMP_IMG is not set +BR2_TARGET_OPENSBI_UBOOT_PAYLOAD=y +BR2_TARGET_UBOOT=y +BR2_TARGET_UBOOT_BUILD_SYSTEM_KCONFIG=y +BR2_TARGET_UBOOT_CUSTOM_TARBALL=y +# HEAD of the Fedora branch +BR2_TARGET_UBOOT_CUSTOM_TARBALL_LOCATION="$(call github,starfive-tech,u-boot,3f3ac01a29ad1cd5fa519d86f81daead2447f1d4)/uboot-3f3ac01a29ad1cd5fa519d86f81daead2447f1d4.tar.gz" +BR2_TARGET_UBOOT_BOARD_DEFCONFIG="starfive_vic7100_beagle_v_smode" +BR2_PACKAGE_HOST_GENIMAGE=y