From 1d09daae030835c673e2fe35c07f88f9ca736b85 Mon Sep 17 00:00:00 2001 From: Paul Mackerras Date: Fri, 5 Jun 2020 13:29:34 +1000 Subject: [PATCH] loadstore1: Complete mfspr/mtspr a cycle later This makes mfspr and mtspr complete (and mfspr write back) on the cycle after the instruction is received from execute1, rather than on the same cycle. This makes them match all other instructions that execute in one cycle. Because these instructions are marked as single-issue, there wasn't the possibility of having two instructions complete on the same cycle (which we can't cope with), but it is better to fix this. Signed-off-by: Paul Mackerras --- loadstore1.vhdl | 32 ++++++++++++++++++-------------- 1 file changed, 18 insertions(+), 14 deletions(-) diff --git a/loadstore1.vhdl b/loadstore1.vhdl index 4140244..e2f3248 100644 --- a/loadstore1.vhdl +++ b/loadstore1.vhdl @@ -42,7 +42,8 @@ architecture behave of loadstore1 is ACK_WAIT, -- waiting for ack from dcache LD_UPDATE, -- writing rA with computed addr on load MMU_LOOKUP, -- waiting for MMU to look up translation - TLBIE_WAIT -- waiting for MMU to finish doing a tlbie + TLBIE_WAIT, -- waiting for MMU to finish doing a tlbie + SPR_CMPLT -- complete a mf/tspr operation ); type reg_stage_t is record @@ -51,6 +52,7 @@ architecture behave of loadstore1 is load : std_ulogic; tlbie : std_ulogic; dcbz : std_ulogic; + mfspr : std_ulogic; addr : std_ulogic_vector(63 downto 0); store_data : std_ulogic_vector(63 downto 0); load_data : std_ulogic_vector(63 downto 0); @@ -73,6 +75,7 @@ architecture behave of loadstore1 is dar : std_ulogic_vector(63 downto 0); dsisr : std_ulogic_vector(31 downto 0); instr_fault : std_ulogic; + sprval : std_ulogic_vector(63 downto 0); end record; type byte_sel_t is array(0 to 7) of std_ulogic; @@ -152,9 +155,7 @@ begin variable use_second : byte_sel_t; variable trim_ctl : trim_ctl_t; variable negative : std_ulogic; - variable mfspr : std_ulogic; variable sprn : std_ulogic_vector(9 downto 0); - variable sprval : std_ulogic_vector(63 downto 0); variable exception : std_ulogic; variable next_addr : std_ulogic_vector(63 downto 0); variable mmureq : std_ulogic; @@ -168,11 +169,10 @@ begin done := '0'; byte_sel := (others => '0'); addr := lsu_sum; - mfspr := '0'; + v.mfspr := '0'; mmu_mtspr := '0'; itlb_fault := '0'; sprn := std_ulogic_vector(to_unsigned(decode_spr_num(l_in.insn), 10)); - sprval := (others => '0'); -- avoid inferred latches exception := '0'; dsisr := (others => '0'); mmureq := '0'; @@ -256,20 +256,20 @@ begin v.tlbie := '1'; v.state := TLBIE_WAIT; when OP_MFSPR => - done := '1'; - mfspr := '1'; + v.mfspr := '1'; -- partial decode on SPR number should be adequate given -- the restricted set that get sent down this path if sprn(9) = '0' and sprn(5) = '0' then if sprn(0) = '0' then - sprval := x"00000000" & r.dsisr; + v.sprval := x"00000000" & r.dsisr; else - sprval := r.dar; + v.sprval := r.dar; end if; else -- reading one of the SPRs in the MMU - sprval := m_in.sprval; + v.sprval := m_in.sprval; end if; + v.state := SPR_CMPLT; when OP_MTSPR => if sprn(9) = '0' and sprn(5) = '0' then if sprn(0) = '0' then @@ -277,7 +277,7 @@ begin else v.dar := l_in.data; end if; - done := '1'; + v.state := SPR_CMPLT; else -- writing one of the SPRs in the MMU mmu_mtspr := '1'; @@ -452,6 +452,10 @@ begin v.state := IDLE; done := '1'; + when SPR_CMPLT => + done := '1'; + v.state := IDLE; + end case; -- Update outputs to dcache @@ -482,10 +486,10 @@ begin -- Multiplex either cache data to the destination GPR or -- the address for the rA update. l_out.valid <= done; - if mfspr = '1' then + if r.mfspr = '1' then l_out.write_enable <= '1'; - l_out.write_reg <= l_in.write_reg; - l_out.write_data <= sprval; + l_out.write_reg <= r.write_reg; + l_out.write_data <= r.sprval; elsif do_update = '1' then l_out.write_enable <= '1'; l_out.write_reg <= r.update_reg; -- 2.30.2