PYTHON3 ?= "python3" .PHONY: help Makefile gitupdate install run_sim test htmlupload gitupdate: git submodule init git submodule update --init --recursive --remote mkpinmux: ./mkpinmux.sh cp pinmux/ls180/ls180_pins.py src/soc/debug cp pinmux/ls180/ls180_pins.py src/soc/litex/florent/libresoc install: gitupdate develop mkpinmux svanalysis pywriter: python3 src/soc/decoder/pseudo/pywriter.py svanalysis: python3 libreriscv/openpower/sv_analysis.py develop: python3 setup.py develop # yes, develop, not install # build and run libresoc litex simulation run_sim: python3 src/soc/simple/issuer_verilog.py --disable-svp64 \ src/soc/litex/florent/libresoc/libresoc.v python3 src/soc/litex/florent/sim.py --cpu=libresoc # and with test gpio (useful for XICS IRC testing) testgpio_run_sim: python3 src/soc/simple/issuer_verilog.py \ src/soc/litex/florent/libresoc/libresoc.v \ --enable-testgpio python3 src/soc/litex/florent/sim.py --cpu=libresoc \ --variant=standardjtagtestgpio ls180_verilog_nopll: python3 src/soc/simple/issuer_verilog.py \ --debug=jtag --enable-core --disable-pll \ --enable-xics --disable-svp64 \ src/soc/litex/florent/libresoc/libresoc.v ls180_verilog: python3 src/soc/simple/issuer_verilog.py \ --debug=jtag --enable-core --enable-pll \ --enable-xics --disable-svp64 \ src/soc/litex/florent/libresoc/libresoc.v ls180_4k_verilog: python3 src/soc/simple/issuer_verilog.py \ --debug=jtag --enable-core --enable-pll \ --enable-xics --enable-sram4x4kblock --disable-svp64 \ src/soc/litex/florent/libresoc/libresoc.v # build the litex libresoc SoC without 4k SRAMs ls180_verilog_build: ls180_verilog make -C soc/soc/litex/florent ls180 # build the litex libresoc SoC with 4k SRAMs ls180_4ksram_verilog_build: ls180_4k_verilog make -C soc/soc/litex/florent ls1804k # testing (usually done at install time) test: install python3 setup.py test # could just run nosetest3... pypiupload: $(PYTHON3) setup.py sdist upload # Minimal makefile for Sphinx documentation # # You can set these variables from the command line. SPHINXOPTS = SPHINXBUILD = sphinx-build SPHINXPROJ = Libre-SOC SOURCEDIR = . BUILDDIR = build # Put it first so that "make" without argument is like "make help". help: @$(SPHINXBUILD) -M help "$(SOURCEDIR)" "$(BUILDDIR)" $(SPHINXOPTS) $(O) # copies all documentation to libre-soc (libre-soc admins only) htmlupload: clean html rsync -HPavz --delete build/html/* \ libre-soc.org:/var/www/libre-soc.org/docs/soc/ # Catch-all target: route all unknown targets to Sphinx using the new # "make mode" option. $(O) is meant as a shortcut for $(SPHINXOPTS). %: Makefile echo "catch-all falling through to sphinx for document building" mkdir -p "$(SOURCEDIR)"/src/gen sphinx-apidoc --ext-autodoc -o "$(SOURCEDIR)"/src/gen ./src/soc @$(SPHINXBUILD) -M $@ "$(SOURCEDIR)" "$(BUILDDIR)" $(SPHINXOPTS) $(O)