broadcom/vc5: Fix height padding of small UIF slices.

The HW doesn't pad the slice's height to make a full 4x4 group of UIF
blocks.  We just need to pad to columns, and the start of the next column
appears in the bottom of the previous column's last block.

Fixes piglit fs-textureOffset-2D.

broadcom/vc5: Print the actual offsets in HW for our resource layout debug.

The alignment of level 0 is non-obvious, so it's hard to turn a faulting
address into a slice without this.

broadcom/vc5: Set the available VS outputs to match the FS inputs.

Fixes piglit glsl-es-3.00/minimum-maximums.txt.

broadcom/vc5: Set the max texture LOD bias.

The field is signed 8.8, so the usual 16.0f fits.  Fixes piglit
gl-2.1-minmax.

broadcom/vc5: Fix translation of stencil ops.

They aren't quite in the same order as the gallium defines.  Fixes piglit
gl-2.0-two-sided-stencil.

broadcom/vc5: Move stencil state packing to the CSO.

Only the stencil ref comes in as dynamic state at emit time.

broadcom/vc5: Introduce a helper for pre-packing our V3DXX structs.

This is so much more pleasant to write than the manual
V3D33_whatever_pack() calls, and will be useful for when we start doing
actual per-V3D compiles.

broadcom/vc5: Add a cl_emit() variant for merging with a pre-packed struct.

Cleans up the hand-written code, at the cost of another ugly macro.

broadcom/vc5: Skip emitting depth offset while disabled.

The enable flag is also in the rasterizer state, so it will be emitted
once it's needed.

broadcom/vc5: Don't emit stencil config if not doing stencil test.

As with blending, we'll have the bit flagged again when it gets reenabled
in CONFIGURATION_BITS, so there's no need to emit test state if we're not
testing.

broadcom/vc5: Don't emit updated blend factors/funcs while disabled.

The dirty bit will be flagged again when re-enbaled.  Keeps us from
emitting blend state in CLs that never do blending.

broadcom/vc5: Fix missing enum decode for indexed primitives.

broadcom/vc5: Drop padding bits from the bottom of the TSDA address.

Fixes misaligned-looking addresses in decode.

broadcom/vc5: Make sure the TMU indirect struct is appropriately aligned.

I was hoping that this would help with fbo-generatemipmap hangs, but no
luck.

broadcom/genxml: Fix decoding of groups with small fields.

Groups containing fields smaller than a byte probably not being decoded
correctly.  For example:

    <group count="32" start="32" size="4">
      <field name="Vertex Element Enables" start="0" end="3" type="uint"/>
    </group>

gen_field_iterator_next would properly walk over each element of the
array, incrementing group_iter.  However, the code to print the actual
values only considered iter->field->start/end, which are 0 and 3 in the
above example.  So it would always fetch bits 3:0 of the current byte,
printing the same value over and over.

Cc: Eric Anholt <eric@anholt.net>

broadcom/vc5: Use DEPTH24_STENCIL8 for rendering to depth-only textures.

The HW puts the pad bits at the top for DEPTH_COMPONENT24, but we need it
at the bottom for texturing.  Using the format with stencil probably means
we won't be able to do Z24 and separate S8, but I wasn't planning on
supporting that anyway.

Fixes hiz-depth-read-fbo-d24-s0

anv: Suffix anv-private 'VK' tokens with 'ANV'

I saw VK_IMAGE_ASPECT_ANY_COLOR_BIT while hacking anv_formats.c and got
confused. "Huh? What extension added that?". No extension defines it;
anv_private.h defines it.

To remove confusion, rename the anv-private VK tokens as if they were
extension tokens with the ANV vendor suffix.

I found only two such tokens:

    VK_IMAGE_ASPECT_ANY_COLOR_BIT
    VK_IMAGE_ASPECT_PLANES_BITS

Reviewed-by: Jason Ekstrand <jason@jlekstrand.net>
Reviewed-by: Lionel Landwerlin <lionel.g.landwerlin@intel.com>

anv: Remove unused variable 'gen'

In anv_physical_device_get_format_properties().

Reviewed-by: Jason Ekstrand <jason@jlekstrand.net>
Reviewed-by: Lionel Landwerlin <lionel.g.landwerlin@intel.com>

radeonsi: add si_screen::has_ls_vgpr_init_bug

Reviewed-by: Nicolai Hähnle <nicolai.haehnle@amd.com>

radeonsi: use ac_create_target_machine

Reviewed-by: Nicolai Hähnle <nicolai.haehnle@amd.com>

radeonsi: use ac_get_llvm_processor_name

Reviewed-by: Nicolai Hähnle <nicolai.haehnle@amd.com>

radeonsi/gfx9: don't set gs_table_depth

Reviewed-by: Nicolai Hähnle <nicolai.haehnle@amd.com>

radeonsi/gfx9: limit the scissor bug workaround to Vega10 and Raven only

Reviewed-by: Nicolai Hähnle <nicolai.haehnle@amd.com>

radeonsi: remove unused field in the PCI ID table

Reviewed-by: Alex Deucher <alexander.deucher@amd.com>

mesa: fix deleting the dummy ATI_fs

The DummyShader is used by GenFragmentShadersATI() as a placeholder to
mark IDs as allocated. Context cleanup wants to delete everything in
ctx->Shared->ATIShaders, and crashes on these placeholders with this
backtrace:
==15060== Invalid free() / delete / delete[] / realloc()
==15060==    at 0x482F478: free (vg_replace_malloc.c:530)
==15060==    by 0x57694F4: _mesa_delete_ati_fragment_shader (atifragshader.c:68)
==15060==    by 0x58B33AB: delete_fragshader_cb (shared.c:208)
==15060==    by 0x5838836: _mesa_HashDeleteAll (hash.c:295)
==15060==    by 0x58B365F: free_shared_state (shared.c:377)
==15060==    by 0x58B3BC2: _mesa_reference_shared_state (shared.c:469)
==15060==    by 0x578687F: _mesa_free_context_data (context.c:1366)
==15060==    by 0x595E9EC: st_destroy_context (st_context.c:642)
==15060==    by 0x5987057: st_context_destroy (st_manager.c:772)
==15060==    by 0x5B018B6: dri_destroy_context (dri_context.c:217)
==15060==    by 0x5B006D3: driDestroyContext (dri_util.c:511)
==15060==    by 0x4A1CBE6: dri3_destroy_context (dri3_glx.c:170)
==15060==  Address 0x7b5dae0 is 0 bytes inside data symbol "DummyShader"

Also, DeleteFragmentShadersATI() should not assert on DummyShader, just
remove the hash entry.

Normally one would define a shader after GenFragmentShadersATI(), and
BindFragmentShaderATI() replaces the placeholder with a real object.
However, the specification doesn't say that one has to define a shader
for each allocated ID.

Signed-off-by: Miklós Máté <mtmkls@gmail.com>
Signed-off-by: Marek Olšák <marek.olsak@amd.com>

gallium: Guard assertions by NDEBUG instead of DEBUG

This matches the standard assert.h header.

Reviewed-by: Eric Engestrom <eric.engestrom@imgtec.com>
Reviewed-by: Marek Olšák <marek.olsak@amd.com>

meson: only turn on Mesa's DEBUG for buildtype==debug

As discussed in this thread:
https://lists.freedesktop.org/archives/mesa-dev/2017-November/175104.html

Cc: Dylan Baker <dylan@pnwbakers.com>
Signed-off-by: Eric Engestrom <eric.engestrom@imgtec.com>
Acked-by: Andres Rodriguez <andresx7@gmail.com>
Reviewed-by: Chad Versace <chadversary@chromium.org>
Reviewed-by: Matt Turner <mattst88@gmail.com>
Tested-by: Chad Versace <chadversary@chromium.org>

meson: switch default build type to debugoptimized

As discussed in this thread:
https://lists.freedesktop.org/archives/mesa-dev/2017-November/175104.html

Cc: Emil Velikov <emil.l.velikov@gmail.com>
Cc: Ilia Mirkin <imirkin@alum.mit.edu>
Cc: Michel Dänzer <michel@daenzer.net>
Cc: Christian Schmidbauer <ch.schmidbauer@gmail.com>
Cc: Eero Tamminen <eero.t.tamminen@intel.com>
Cc: Ernst Sjöstrand <ernstp@gmail.com>
Signed-off-by: Eric Engestrom <eric.engestrom@imgtec.com>
Acked-by: Matt Turner <mattst88@gmail.com>
Acked-by: Andres Rodriguez <andresx7@gmail.com>
Acked-by: Emil Velikov <emil.velikov@collabora.com>
Reviewed-by: Dylan Baker <dylan@pnwbakers.com>
Reviewed-by: Chad Versace <chadversary@chromium.org>
Tested-by: Chad Versace <chadversary@chromium.org>

meson: drop GLESv1 .so version back to 1.0.0

autotools generates libGLESv1_CM.so.1.0.0, so let's make sure meson
does the same.

Signed-off-by: Eric Engestrom <eric@engestrom.ch>
Reviewed-by: Dylan Baker <dylan@pnwbakers.com>

meson: standardize .so version to major.minor.patch

This `version` field defines the filename for the .so.
The plan .so as well as .so.$major are always symlinks to this.

Unless I'm mistaken, only the major is ever used, so this shouldn't
matter, but for consistency with autotools (and in case it does matter),
let's always have all 3 major.minor.patch components.

(The soname isn't affected, and is always .so.$major)

Signed-off-by: Eric Engestrom <eric@engestrom.ch>
Reviewed-by: Dylan Baker <dylan@pnwbakers.com>

ac/nir: for ubo load use correct num_components

I was hacking something stupid in doom, and hit an assert for the bitcast
following this, it definitely looks like this should be the number of 32-bit
components, not the instr level ones.

Reviewed-by: Nicolai Hähnle <nicolai.haehnle@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

nir: fix a typo

Signed-off-by: Mun Gwan-gyeong <elongbug@gmail.com>
Reviewed-by: Dylan Baker <dylan@pnwbakers.com>

glsl: Allow precision mismatch on dead data with GLSL ES 1.00

Commit 259fc505454ea6a67aeacf6cdebf1398d9947759 added linker error for
mismatching uniform precision, as required by GLES 3.0 specification and
conformance test-suite.

Several Android applications, including Forge of Empires, have shaders
which violate this rule, on a dead varying that will be eliminated.
The problem affects a big number of applications using Cocos2D engine
and other GLES implementations accept this, this poses a serious
application compatibility issue.

Starting from GLSL ES 3.0, declarations with conflicting precision
qualifiers are explicitly prohibited. However GLSL ES 1.00 does not
clearly specify the behavior, except that

  "Uniforms are defined to behave as if they are using the same storage in
  the vertex and fragment processors and may be implemented this way.
  If uniforms are used in both the vertex and fragment shaders, developers
  should be warned if the precisions are different. Conversion of
  precision should never be implicit."

The word "used" is not clear in this context and might refer to
 1) declared (same as GLES 3.x)
 2) referred after post-processing, or
 3) linked after all optimizations are done.

Looking at existing applications, 2) or 3) seems to be widely adopted.
To avoid compatibility issues, turn the error into a warning if GLSL ES
version is lower than 3.0 and the data is dead in at least one of the
shaders.

Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=97532
Signed-off-by: Tomasz Figa <tfiga@chromium.org>
Reviewed-by: Kenneth Graunke <kenneth@whitecape.org>

i965: disable NIR linking on HSW and below

Fixes: 379b24a40d3d "i965: make use of nir linking"
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=103537
Reviewed-by: Iago Toral Quiroga <itoral@igalia.com>

radv: move is_local up to the winsys level.

We can avoid adding the buffer in the non-local case, this will
avoid all the overhead of the indirect call.

Reviewed-by: Samuel Pitoiset <samuel.pitoiset@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

radv: wrap cs_add_buffer in an inline. (v2)

The next patch will try and avoid calling the indirect function.

v2: add a missing conversion.

Reviewed-by: Samuel Pitoiset <samuel.pitoiset@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

radv: when loading regs no need to add buffer

The function that calls us has just added the buffer to the
list already, no need to try and add it again.

Reviewed-by: Samuel Pitoiset <samuel.pitoiset@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

radv: pre-calculate user_data_0 registers and store in pipeline

There's no point recalculating these the whole time on descriptor
emission, just store them at pipeline creation.

Reviewed-by: Samuel Pitoiset <samuel.pitoiset@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

docs: Mark GLX_ARB_context_flush_control done

Requires an unreleased X server, but from the client GLX side this is as
done as it gets.

Signed-off-by: Adam Jackson <ajax@redhat.com>

i965: Enable flush control

Reviewed-by: Adam Jackson <ajax@redhat.com>
Reviewed-by: Nicolai Hähnle <nicolai.haehnle@amd.com>
Reviewed-by: Emil Velikov <emil.velikov@collabora.com>
Reviewed-by: Kenneth Graunke <kenneth@whitecape.org>
Signed-off-by: Neil Roberts <neil@linux.intel.com>

drisw: Enable flush control for llvmpipe and softpipe

Hilariously this is a fairly big win.  Neil's multi-context-test
improves from ~24 to ~36 fps with llvmpipe on a Core i5-3317U.  softpipe
also improves, from about 2.25 to 3.09 fps (when it's that slow, you're
allowed to be that precise).

I'd have added it to swrast classic, but the testcase wants GL 3.0 and
shaders, and that's not a thing classic has, so I figured making it work
on softpipe was crime enough.

Reviewed-by: Marek Olšák <marek.olsak@amd.com>
Reviewed-by: Nicolai Hähnle <nicolai.haehnle@amd.com>
Reviewed-by: Emil Velikov <emil.velikov@collabora.com>
Signed-off-by: Adam Jackson <ajax@redhat.com>

gallium: Wire up flush control

Reviewed-by: Marek Olšák <marek.olsak@amd.com>
Reviewed-by: Nicolai Hähnle <nicolai.haehnle@amd.com>
Reviewed-by: Emil Velikov <emil.velikov@collabora.com>
Signed-off-by: Adam Jackson <ajax@redhat.com>

egl: Implement EGL_KHR_context_flush_control

Reviewed-by: Nicolai Hähnle <nicolai.haehnle@amd.com>
Reviewed-by: Emil Velikov <emil.velikov@collabora.com>
Signed-off-by: Adam Jackson <ajax@redhat.com>

glx: Implement GLX_ARB_context_flush_control

Reviewed-by: Adam Jackson <ajax@redhat.com>
Reviewed-by: Nicolai Hähnle <nicolai.haehnle@amd.com>
Reviewed-by: Emil Velikov <emil.velikov@collabora.com>
Signed-off-by: Neil Roberts <neil@linux.intel.com>

dri: Add a flush control extension

This advertises that the driver can accept a new context attribute
__DRI_CTX_ATTRIB_RELEASE_BEHAVIOR.

Reviewed-by: Adam Jackson <ajax@redhat.com>
Reviewed-by: Nicolai Hähnle <nicolai.haehnle@amd.com>
Reviewed-by: Emil Velikov <emil.velikov@collabora.com>
Signed-off-by: Neil Roberts <neil@linux.intel.com>

dri: Change __DriverApiRec::CreateContext to take a struct for attribs

Previously the CreateContext method of __DriverApiRec took a set of
arguments to describe the attribute values from the window system API's
CreateContextAttribs function. As more attributes get added this could
quickly get unworkable and every new attribute needs a modification for
every driver.

To fix that, pass the attribute values in a struct instead.  The struct
has a bitmask to specify which members are used. The first three members
(two for the GL version and one for the flags) are always set. If the
bit is not set in the attribute mask then it can be assumed the
attribute has the default value. Drivers will error if unknown bits in
the mask are set.

Reviewed-by: Adam Jackson <ajax@redhat.com>
Reviewed-by: Nicolai Hähnle <nicolai.haehnle@amd.com>
Reviewed-by: Emil Velikov <emil.velikov@collabora.com>
Signed-off-by: Neil Roberts <neil@linux.intel.com>

intel: Don't flush the old context in intelMakeCurrent

It shouldn't be necessary to flush the context within the driver
implementation because the old context is explicitly flushed in
_mesa_make_current which is called a little further on. It is useful to
only have a single place that flushes when switching contexts to make it
easier to later implement the GL_KHR_context_flush_control extension.

The flush in intelMakeCurrent was added in commit 5505865 to implement
the GLX semantics that the context should be flushed when it is
released.  When the commit was made there was no flush in
_mesa_make_current because it was only added later in 93102b4c. I think
that later commit effectively makes the first commit redundant.

Reviewed-by: Adam Jackson <ajax@redhat.com>
Reviewed-by: Emil Velikov <emil.velikov@collabora.com>
Reviewed-by: Kenneth Graunke <kenneth@whitecape.org>
Signed-off-by: Neil Roberts <neil@linux.intel.com>

egl/dri2: Factor out context attribute initialization

Signed-off-by: Adam Jackson <ajax@redhat.com>
Reviewed-by: Eric Engestrom <eric.engestrom@imgtec.com>
Reviewed-by: Nicolai Hähnle <nicolai.haehnle@amd.com>
Reviewed-by: Emil Velikov <emil.velikov@collabora.com>

etnaviv: Don't over-pad compressed textures

HALIGN_FOUR/SIXTEEN has no meaning for compressed textures, and we can't
render to them anyway. So use the tightest possible packing. This
avoids bugs with non-power-of-two block sizes.

Signed-off-by: Wladimir J. van der Laan <laanwj@gmail.com>
Reviewed-by: Christian Gmeiner <christian.gmeiner@gmail.com>

etnaviv: ASTC texture support

Add ASTC texture support for hardware that supports this
(currently only GC3000 on i.MX6qp is known to have this).

Signed-off-by: Wladimir J. van der Laan <laanwj@gmail.com>
Reviewed-by: Christian Gmeiner <christian.gmeiner@gmail.com>

etnaviv: Update from rnndb

Updated as of etnav_viv commit 3b4a8ec.

Signed-off-by: Wladimir J. van der Laan <laanwj@gmail.com>
Reviewed-by: Christian Gmeiner <christian.gmeiner@gmail.com>

radv: add initial copy descriptor support. (v2)

It appears the latest dota2 vulkan uses this,
and we get a hang in VR mode without it.

v2: remove finishme I left in after finishing.

Reviewed-by: Bas Nieuwenhuizen <bas@basnieuwenhuizen.nl>
Reviewed-by: Andres Rodriguez <andresx7@gmail.com>
Cc: "17.2 17.3" <mesa-stable@lists.freedesktop.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>

gallium/u_vbuf: use signed vertex buffers offsets for optimal uploads

Uploaded data must start at (stride * start), because we can't modify
start in all cases. If it's the first allocation, it's also the amount
of memory wasted. If the starting offset is larger than the size of
the upload buffer, the buffer is re-created, used for 1 upload, and then
thrown away. If the upload is small, most of the buffer space is unused
and wasted. Keep doing that and the OOM killer comes. It's actually
pretty quick.

With signed VB offsets, we can set min_out_offset = 0
in u_upload_alloc/u_upload_data.

This fixes OOM situations with SPECviewperf.

radeonsi: enable signed vertex buffer offsets

gallium: add PIPE_CAP_SIGNED_VERTEX_BUFFER_OFFSET

automake: include git_sha1.h.in in release tarball

Fixes:

make[2]: Leaving directory '/home/local/mesa/mesa-17.4.0-devel/_build/sub/src'
make[2]: *** No rule to make target '../../../src/git_sha1.h.in', needed by 'git_sha1.h'.  Stop.
Makefile:660: recipe for target 'all-recursive' failed

Fixes: 16be271c6ee618e79c7d "git_sha1_gen: use git_sha1.h.in on all build systems"
Reviewed-by: Eric Engestrom <eric.engestrom@imgtec.com>
Signed-off-by: Juan A. Suarez Romero <jasuarez@igalia.com>

radeonsi: don't map big VRAM buffers for the first upload directly

Reviewed-by: Nicolai Hähnle <nicolai.haehnle@amd.com>

gallium/u_threaded: don't map big VRAM buffers for the first upload directly

This improves Paraview "many spheres" performance 4x along with the radeonsi
commit.

Reviewed-by: Nicolai Hähnle <nicolai.haehnle@amd.com>

gallium/u_threaded: clean up tc_improve_map_buffer_flags and prevent reentry

Reviewed-by: Nicolai Hähnle <nicolai.haehnle@amd.com>

radv: move descriptor sets out of cmd_state.

Instead of storing all the pointers and zeroing them all out,
just store a valid bitmask in the state. This also moves
the CmdBindPipeline path down the cpu usage path for the
multithreading demo as it no longer has to traverse MAX_SETS
to find the active descriptor sets.

Reviewed-by: Bas Nieuwenhuizen <bas@basnieuwenhuizen.nl>
Signed-off-by: Dave Airlie <airlied@redhat.com>

radv: add helper for setting a descriptor.

This is just a simple refactor.

Reviewed-by: Bas Nieuwenhuizen <bas@basnieuwenhuizen.nl>
Signed-off-by: Dave Airlie <airlied@redhat.com>

radv: move vertex binding out of cmd state.

This isn't required to be cleared, since buffers are only linked
by vertex elements, so if elements are clear then no buffers
should be referenced.

Reviewed-by: Bas Nieuwenhuizen <bas@basnieuwenhuizen.nl>
Signed-off-by: Dave Airlie <airlied@redhat.com>

radv: reorder cmd_state to remove a hole.

This just removes a hole in the cmd_state and packs some bools
together.

Reviewed-by: Bas Nieuwenhuizen <bas@basnieuwenhuizen.nl>
Signed-off-by: Dave Airlie <airlied@redhat.com>

radv: free attachments on end command buffer.

If we allocate attachments in the begin command buffer due to the
render pass continue bit, we were leaking them.

Since renderpasses inside a cmd buffer malloc/free these properly,
and set to NULL, we just need to call free at end.

Fixes a memory leak with multithreading demo.

Reviewed-by: Bas Nieuwenhuizen <bas@basnieuwenhuizen.nl>
Cc: "17.2 17.3" <mesa-stable@lists.freedesktop.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>

radv: Optimize calling radv_save_descriptors.

uint32_t data[MAX_SETS * 2] = {}; was getting executed before
the exit and took significant amounts of time. By having the
check outside the function, we skip the execution of the clear.

Reviewed-by: Dave Airlie <airlied@redhat.com>

radv: Use an array to store descriptor sets.

The vram_list linked list resulted in lots of pointer chasing.
Replacing this with an array instead improves descriptor set
allocation CPU usage by 3x at least (when also considering the free),
because it had to iterate through 300-400 sets on average.

Not a huge improvement as the pre-improvement CPU usage was only
about 2.3% in the busiest thread.

Reviewed-by: Dave Airlie <airlied@redhat.com>

nv50,nvc0: Display shared memory usage in pipe_debug_message

Signed-off-by: Pierre Moreau <pierre.morrow@free.fr>

nv50,nvc0: Copy shared memory per block to the program info structure and back

In OpenCL/CUDA kernels, shared memory usage can be defined within the
kernel code. Those usage will only be picked up while parsing the
SPIR-V, during the translation phase of the program.

Signed-off-by: Pierre Moreau <pierre.morrow@free.fr>

nv50/ir: Store shared memory per block in nv50_ir_prog_info

Signed-off-by: Pierre Moreau <pierre.morrow@free.fr>

i965/gen10: Implement Wa3DStateMode

This workaround doesn't fix any of the piglit hangs we've seen
on CNL. But it might be fixing something we haven't tested yet.

V2: Remove the bits enabling Float blend optimization. It is
    enabled through CACHE_MODE_SS register.
    Update the comment.
    Move gen10 if block on top of gen9 if block.

Signed-off-by: Anuj Phogat <anuj.phogat@gmail.com>
Reviewed-by: Rafael Antognolli <rafael.antognolli@intel.com>
Reviewed-by: Nanley Chery <nanley.g.chery@intel.com>

i965/gen10: Enable float blend optimization

This optimization is enabled for previous generations too.
See Mesa commit c17e214a6b
On CNL this bit has been moved to CACHE_MODE_SS register.

Signed-off-by: Anuj Phogat <anuj.phogat@gmail.com>
Reviewed-by: Nanley Chery <nanley.g.chery@intel.com>

i965/gen10: Implement WaForceRCPFEHangWorkaround

This workaround doesn't fix any of the piglit hangs we've seen
on CNL. But it might be fixing something we haven't tested yet.

V2: Add the check for Post Sync Operation.
    Update the workaround comment.
    Use braces around if-else.

Signed-off-by: Anuj Phogat <anuj.phogat@gmail.com>
Reviewed-by: Rafael Antognolli <rafael.antognolli@intel.com>
Reviewed-by: Nanley Chery <nanley.g.chery@intel.com>

i965/gen10: Implement WaSampleOffsetIZ workaround

There are few other (duplicate) workarounds which have similar recommendations:
WaFlushHangWhenNonPipelineStateAndMarkerStalled
WaCSStallBefore3DSamplePattern
WaPipeControlBefore3DStateSamplePattern

WaPipeControlBefore3DStateSamplePattern has some extra recommendations if
driver is using mid batch context restore. Ignoring it for now because We're
not doing mid-batch context restore in Mesa.

This workaround doesn't fix any of the piglit hangs we've seen
on CNL. But it might be fixing something we haven't tested yet.

V2: Use brw_load_register_imm32() to program CACHE_MODE_0.
    Get rid of brw_flush_gpu_caches().

V3: Make the workaround helper functions static.

Signed-off-by: Anuj Phogat <anuj.phogat@gmail.com>
Reviewed-by: Rafael Antognolli <rafael.antognolli@intel.com>
Reviewed-by :Nanley Chery <nanley.g.chery@intel.com>

i965/gen10: Don't set Antialiasing Enable in 3DSTATE_RASTER if num_samples > 1

Signed-off-by: Anuj Phogat <anuj.phogat@gmail.com>
Reviewed-by: Kenneth Graunke <kenneth@whitecape.org>

i965/gen10: Don't set Smooth Point Enable in 3DSTATE_SF if num_samples > 1

Signed-off-by: Anuj Phogat <anuj.phogat@gmail.com>
Reviewed-by: Kenneth Graunke <kenneth@whitecape.org>

winsys/amdgpu: Add R600_DEBUG flag to reserve VMID per ctx.

Fixes reverted patch f03b7c9 by doing VMID reservation per
process and not per context.
Also updates required amdgpu libdrm version since the change
involved interface updates in amdgpu libdrm.

Signed-off-by: Andrey Grodzovsky <andrey.grodzovsky@amd.com>
Signed-off-by: Marek Olšák <marek.olsak@amd.com>

i965: perf: list registers to program for queries

Signed-off-by: Lionel Landwerlin <lionel.g.landwerlin@intel.com>
Reviewed-by: Kenneth Graunke <kenneth@whitecape.org>

i965: perf: factorize code for availability

Signed-off-by: Lionel Landwerlin <lionel.g.landwerlin@intel.com>
Reviewed-by: Kenneth Graunke <kenneth@whitecape.org>

i965: perf: make revision variable available

This will be used in the next commit to build up register programming.

Signed-off-by: Lionel Landwerlin <lionel.g.landwerlin@intel.com>
Reviewed-by: Kenneth Graunke <kenneth@whitecape.org>

glsl: fix interpolateAtXxx(some_vec[idx], ...) with dynamic idx

The dynamic index of a vector (not array!) is lowered to a sequence of
conditional assignments. However, the interpolate_at_* expressions
require that the interpolant is an l-value of a shader input.

So instead of doing conditional assignments of parts of the shader input
and then interpolating that (which is nonsensical), we interpolate the
entire shader input and then do conditional assignments of the interpolated
result.

Reviewed-by: Timothy Arceri <tarceri@itsqueeze.com>

glsl: allow any l-value of an input variable as interpolant in interpolateAt*

The intended rule has been clarified in GLSL 4.60, Section 8.13.2
(Interpolation Functions):

   "For all of the interpolation functions, interpolant must be an l-value
    from an in declaration; this can include a variable, a block or
    structure member, an array element, or some combination of these.
    Component selection operators (e.g., .xy) may be used when specifying
    interpolant."

For members of interface blocks, var->data.must_be_shader_input must be
determined on-the-fly after lowering interface blocks, since we don't want
to disable varying packing for an entire block just because one input in it
is used in interpolateAt*.

v2: keep setting must_be_shader_input in ast_function (Ian)
v3: follow the relaxed rule of GLSL 4.60
v4: only apply the relaxed rules to desktop GL
    (the ES WG decided that the relaxed rules may apply in a future version
     but not retroactively; see also
     dEQP-GLES31.functional.shaders.multisample_interpolation.interpolate_at_centroid.negative.*)

Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=101378
Reviewed-by: Ian Romanick <ian.d.romanick@intel.com> (v1)
Reviewed-by: Timothy Arceri <tarceri@itsqueeze.com>

nir/serialize: fix build with gcc 4.4.7

I had to build on RHEL6 today, and noticed this.

Reviewed-by: Jason Ekstrand <jason@jlekstrand.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>

i915g: remove some unknown cap warnings.

i915g: make gears run again.

We need to validate some structs exist before we dirty the states, and
avoid the problem in some other places.

Fixes: e027935a7 ("st/mesa: don't update unrelated states in non-draw calls such as Clear")

ac: remove the remaining duplicate llvm types

Reviewed-by: Marek Olšák <marek.olsak@amd.com
Acked-by: Nicolai Hähnle <nicolai.haehnle@amd.com>

ac: remove usused v4f32

Reviewed-by: Marek Olšák <marek.olsak@amd.com
Acked-by: Nicolai Hähnle <nicolai.haehnle@amd.com>

ac: add v2f32 to the common code and make use of it

Reviewed-by: Marek Olšák <marek.olsak@amd.com
Acked-by: Nicolai Hähnle <nicolai.haehnle@amd.com>

ac: use the ac f16 llvm type

Reviewed-by: Marek Olšák <marek.olsak@amd.com
Acked-by: Nicolai Hähnle <nicolai.haehnle@amd.com>

ac: use the ac f32 llvm type

Reviewed-by: Marek Olšák <marek.olsak@amd.com
Acked-by: Nicolai Hähnle <nicolai.haehnle@amd.com>

ac: use the ac f64 llvm type

Reviewed-by: Marek Olšák <marek.olsak@amd.com
Acked-by: Nicolai Hähnle <nicolai.haehnle@amd.com>

ac: use the common v8i32 llvm type

Reviewed-by: Marek Olšák <marek.olsak@amd.com
Acked-by: Nicolai Hähnle <nicolai.haehnle@amd.com>

ac: use the common v4i32 llvm type

Reviewed-by: Marek Olšák <marek.olsak@amd.com
Acked-by: Nicolai Hähnle <nicolai.haehnle@amd.com>

ac: add v3i32 to the common code and make use of it

Reviewed-by: Marek Olšák <marek.olsak@amd.com
Acked-by: Nicolai Hähnle <nicolai.haehnle@amd.com>

ac: add v2i32 to the common code and use it

Reviewed-by: Marek Olšák <marek.olsak@amd.com
Acked-by: Nicolai Hähnle <nicolai.haehnle@amd.com>

ac: use the ac i64 llvm type

Reviewed-by: Dave Airlie <airlied@redhat.com>
Reviewed-by: Marek Olšák <marek.olsak@amd.com
Acked-by: Nicolai Hähnle <nicolai.haehnle@amd.com>

ac: remove unused i16 llvm type

Reviewed-by: Dave Airlie <airlied@redhat.com>
Reviewed-by: Marek Olšák <marek.olsak@amd.com
Acked-by: Nicolai Hähnle <nicolai.haehnle@amd.com>

ac: use the ac ivoidt llvm type

Reviewed-by: Dave Airlie <airlied@redhat.com>
Reviewed-by: Marek Olšák <marek.olsak@amd.com
Acked-by: Nicolai Hähnle <nicolai.haehnle@amd.com>

ac: use the ac i8 llvm type

Reviewed-by: Dave Airlie <airlied@redhat.com>
Reviewed-by: Marek Olšák <marek.olsak@amd.com
Acked-by: Nicolai Hähnle <nicolai.haehnle@amd.com>

ac: use the ac i1 llvm type

Reviewed-by: Dave Airlie <airlied@redhat.com>
Reviewed-by: Marek Olšák <marek.olsak@amd.com
Acked-by: Nicolai Hähnle <nicolai.haehnle@amd.com>

ac: use the ac i32 llvm type

Reviewed-by: Dave Airlie <airlied@redhat.com>
Reviewed-by: Marek Olšák <marek.olsak@amd.com
Acked-by: Nicolai Hähnle <nicolai.haehnle@amd.com>