from nmigen import Module, Signal, Mux, Elaboratable, Array, Cat
from nmutil.iocontrol import RecordObject
from nmigen.utils import log2_int
+from nmigen.hdl.rec import Record, Layout
from nmutil.latch import SRLatch, latchregister
from soc.decoder.power_decoder2 import Data
from soc.decoder.power_enums import InternalOp
+from soc.regfile.regfile import ortreereduce
+from nmutil.util import treereduce
from soc.experiment.compldst import CompLDSTOpSubset
from soc.decoder.power_decoder2 import Data
# for testing purposes
from soc.experiment.testmem import TestMemory
-
class PortInterface(RecordObject):
"""PortInterface
# distinguish op type (ld/st)
self.is_ld_i = Signal(reset_less=True)
self.is_st_i = Signal(reset_less=True)
- self.op = CompLDSTOpSubset() # hm insn_type ld/st duplicates here
+ self.op = CompLDSTOpSubset() # hm insn_type ld/st duplicates here
# common signals
self.busy_o = Signal(reset_less=True) # do not use if busy
self.go_die_i = Signal(reset_less=True) # back to reset
self.addr = Data(addrwid, "addr_i") # addr/addr-ok
- self.addr_ok_o = Signal(reset_less=True) # addr is valid (TLB, L1 etc.)
- self.addr_exc_o = Signal(reset_less=True) # TODO, "type" of exception
+ # addr is valid (TLB, L1 etc.)
+ self.addr_ok_o = Signal(reset_less=True)
+ self.addr_exc_o = Signal(reset_less=True) # TODO, "type" of exception
# LD/ST
- self.ld = Data(regwid, "ld_data_o") # ok to be set by L0 Cache/Buf
- self.st = Data(regwid, "st_data_i") # ok to be set by CompUnit
+ self.ld = Data(regwid, "ld_data_o") # ok to be set by L0 Cache/Buf
+ self.st = Data(regwid, "st_data_i") # ok to be set by CompUnit
+
+# TODO:
+
+
+class DualPortSplitter(Elaboratable):
+ """DualPortSplitter
+
+ * one incoming PortInterface
+ * two *OUTGOING* PortInterfaces
+ * uses LDSTSplitter to do it
+
+ (actually, thinking about it LDSTSplitter could simply be
+ modified to conform to PortInterface: one in, two out)
+
+ once that is done each pair of ports may be wired directly
+ to the dual ports of L0CacheBuffer
+ """
+ pass
+
+
+class DataMergerRecord(Record):
+ """
+ {data: 128 bit, byte_enable: 16 bit}
+ """
+
+ def __init__(self, name=None):
+ layout = (('data', 128),
+ ('en', 16)
+ )
+
+ Record.__init__(self, Layout(layout), name=name)
+
+ #FIXME: make resetless
+
+# TODO: formal verification
+
+class DataMerger(Elaboratable):
+ """DataMerger
+
+ Merges data based on an address-match matrix.
+ Identifies (picks) one (any) row, then uses that row,
+ based on matching address bits, to merge (OR) all data
+ rows into the output.
+
+ Basically, by the time DataMerger is used, all of its incoming data is
+ determined not to conflict. The last step before actually submitting
+ the request to the Memory Subsystem is to work out which requests,
+ on the same 128-bit cache line, can be "merged" due to them being:
+ (A) on the same address (bits 4 and above) (B) having byte-enable
+ lines that (as previously mentioned) do not conflict.
+
+ Therefore, put simply, this module will:
+ (1) pick a row (any row) and identify it by an index labelled "idx"
+ (2) merge all byte-enable lines which are on that same address, as
+ indicated by addr_match_i[idx], onto the output
+ """
+
+ def __init__(self, array_size):
+ """
+ :addr_array_i: an NxN Array of Signals with bits set indicating address
+ match. bits across the diagonal (addr_array_i[x][x])
+ will always be set, to indicate "active".
+ :data_i: an Nx Array of Records {data: 128 bit, byte_enable: 16 bit}
+ :data_o: an Output Record of same type
+ {data: 128 bit, byte_enable: 16 bit}
+ """
+ self.array_size = array_size
+ ul = []
+ for i in range(array_size):
+ ul.append(Signal(array_size,
+ reset_less=True,
+ name="addr_match_%d" % i))
+ self.addr_array_i = Array(ul)
+
+ ul = []
+ for i in range(array_size):
+ ul.append(DataMergerRecord())
+ self.data_i = Array(ul)
+ self.data_o = DataMergerRecord()
+
+ def elaborate(self, platform):
+ m = Module()
+ comb = m.d.comb
+ #(1) pick a row
+ m.submodules.pick = pick = PriorityEncoder(self.array_size)
+ for j in range(self.array_size):
+ comb += pick.i[j].eq(self.addr_array_i[j].bool())
+ valid = ~pick.n
+ idx = pick.o
+ #(2) merge
+ with m.If(valid):
+ l = []
+ for j in range(self.array_size):
+ select = self.addr_array_i[idx][j]
+ r = DataMergerRecord()
+ with m.If(select):
+ comb += r.eq(self.data_i[j])
+ l.append(r)
+ comb += self.data_o.data.eq(ortreereduce(l,"data"))
+ comb += self.data_o.en.eq(ortreereduce(l,"en"))
+
+ return m
class LDSTPort(Elaboratable):
combinatorially, where a nmigen FSM's state-changes only activate
on clock-sync boundaries.
"""
+
def __init__(self, n_units, mem, regwid=64, addrwid=48):
self.n_units = n_units
self.mem = mem
m.submodules.st_active = st_active = SRLatch(False, name="st_active")
m.submodules.ld_active = ld_active = SRLatch(False, name="ld_active")
m.submodules.reset_l = reset_l = SRLatch(True, name="reset")
- m.submodules.idx_l = idx_l = SRLatch(False, name="idx_l")
+ m.submodules.idx_l = idx_l = SRLatch(False, name="idx_l")
m.submodules.adrok_l = adrok_l = SRLatch(False, name="addr_acked")
# find one LD (or ST) and do it. only one per cycle.
sti = []
for i in range(self.n_units):
pi = self.dports[i].pi
- ldi.append(pi.is_ld_i & pi.busy_o) # accumulate ld-req signals
- sti.append(pi.is_st_i & pi.busy_o) # accumulate st-req signals
+ ldi.append(pi.is_ld_i & pi.busy_o) # accumulate ld-req signals
+ sti.append(pi.is_st_i & pi.busy_o) # accumulate st-req signals
# put the requests into the priority-pickers
comb += ldpick.i.eq(Cat(*ldi))
comb += stpick.i.eq(Cat(*sti))
ld_idx = Signal(nbits, reset_less=False)
st_idx = Signal(nbits, reset_less=False)
# use these because of the sync-and-comb pass-through capability
- latchregister(m, ldpick.o, ld_idx, idx_l.qn, name="ld_idx")
- latchregister(m, stpick.o, st_idx, idx_l.qn, name="st_idx")
+ latchregister(m, ldpick.o, ld_idx, idx_l.qn, name="ld_idx_l")
+ latchregister(m, stpick.o, st_idx, idx_l.qn, name="st_idx_l")
# convenience variables to reference the "picked" port
ldport = self.dports[ld_idx].pi
sync += adrok_l.s.eq(0)
comb += adrok_l.r.eq(0)
with m.If(~ldpick.n):
- comb += ld_active.s.eq(1) # activate LD mode
+ comb += ld_active.s.eq(1) # activate LD mode
comb += idx_l.r.eq(1) # pick (and capture) the port index
- comb += adrok_l.r.eq(1) # address not yet "ok'd"
with m.Elif(~stpick.n):
- comb += st_active.s.eq(1) # activate ST mode
+ comb += st_active.s.eq(1) # activate ST mode
comb += idx_l.r.eq(1) # pick (and capture) the port index
- comb += adrok_l.r.eq(1) # address not yet "ok'd"
# from this point onwards, with the port "picked", it stays picked
# until ld_active (or st_active) are de-asserted.
# if now in "LD" mode: wait for addr_ok, then send the address out
# to memory, acknowledge address, and send out LD data
with m.If(ld_active.q):
- with m.If(ldport.addr.ok):
- comb += rdport.addr.eq(ldport.addr.data) # addr ok, send thru
- with m.If(adrok_l.qn):
- comb += ldport.addr_ok_o.eq(1) # acknowledge addr ok
- sync += adrok_l.s.eq(1) # and pull "ack" latch
+ with m.If(ldport.addr.ok & adrok_l.qn):
+ comb += rdport.addr.eq(ldport.addr.data) # addr ok, send thru
+ comb += ldport.addr_ok_o.eq(1) # acknowledge addr ok
+ sync += adrok_l.s.eq(1) # and pull "ack" latch
# if now in "ST" mode: likewise do the same but with "ST"
# to memory, acknowledge address, and send out LD data
with m.If(st_active.q):
with m.If(stport.addr.ok):
- comb += wrport.addr.eq(stport.addr.data) # addr ok, send thru
+ comb += wrport.addr.eq(stport.addr.data) # addr ok, send thru
with m.If(adrok_l.qn):
- comb += stport.addr_ok_o.eq(1) # acknowledge addr ok
+ comb += stport.addr_ok_o.eq(1) # acknowledge addr ok
sync += adrok_l.s.eq(1) # and pull "ack" latch
# NOTE: in both these, below, the port itself takes care
comb += reset_l.s.eq(0)
comb += reset_l.r.eq(0)
with m.If(ld_active.q & adrok_l.q):
- comb += ldport.ld.data.eq(rdport.data) # put data out
+ comb += ldport.ld.data.eq(rdport.data) # put data out
comb += ldport.ld.ok.eq(1) # indicate data valid
comb += reset_l.s.eq(1) # reset mode after 1 cycle
# for ST mode, when addr has been "ok'd", wait for incoming "ST ok"
with m.If(st_active.q & stport.st.ok):
- comb += wrport.data.eq(stport.st.data) # write st to mem
+ comb += wrport.data.eq(stport.st.data) # write st to mem
comb += wrport.en.eq(1) # enable write
comb += reset_l.s.eq(1) # reset mode after 1 cycle
+ # after waiting one cycle (reset_l is "sync" mode), reset the port
with m.If(reset_l.q):
comb += idx_l.s.eq(1) # deactivate port-index selector
comb += ld_active.r.eq(1) # leave the ST active for 1 cycle
comb += st_active.r.eq(1) # leave the ST active for 1 cycle
comb += reset_l.r.eq(1) # clear reset
+ comb += adrok_l.r.eq(1) # address reset
return m
yield self.mem.wrport.data
# TODO: mem ports
+
def wait_busy(port, no=False):
while True:
busy = yield port.pi.busy_o
- print ("busy", no, busy)
+ print("busy", no, busy)
if bool(busy) == no:
break
yield
def wait_addr(port):
while True:
addr_ok = yield port.pi.addr_ok_o
- print ("addrok", addr_ok)
+ print("addrok", addr_ok)
if not addr_ok:
break
yield
+
def wait_ldok(port):
while True:
ldok = yield port.pi.ld.ok
- print ("ldok", ldok)
+ print("ldok", ldok)
if ldok:
break
yield
+
def l0_cache_st(dut, addr, data):
l0 = dut.l0
mem = dut.mem
yield from wait_busy(port1, no=False) # wait until not busy
# set up a ST on the port. address first:
- yield port1.pi.is_st_i.eq(1) # indicate LD
+ yield port1.pi.is_st_i.eq(1) # indicate LD
- yield port1.pi.addr.data.eq(addr) # set address
- yield port1.pi.addr.ok.eq(1) # set ok
+ yield port1.pi.addr.data.eq(addr) # set address
+ yield port1.pi.addr.ok.eq(1) # set ok
yield from wait_addr(port1) # wait until addr ok
-
+ # yield # not needed, just for checking
+ # yield # not needed, just for checking
# assert "ST" for one cycle (required by the API)
yield port1.pi.st.data.eq(data)
yield port1.pi.st.ok.eq(1)
yield port1.pi.st.ok.eq(0)
# can go straight to reset.
- yield port1.pi.is_st_i.eq(0) #end
- yield port1.pi.addr.ok.eq(0) # set !ok
- yield from wait_busy(port1, True) # wait until not busy
+ yield port1.pi.is_st_i.eq(0) # end
+ yield port1.pi.addr.ok.eq(0) # set !ok
+ # yield from wait_busy(port1, False) # wait until not busy
def l0_cache_ld(dut, addr, expected):
yield from wait_busy(port1, no=False) # wait until not busy
# set up a LD on the port. address first:
- yield port1.pi.is_ld_i.eq(1) # indicate LD
+ yield port1.pi.is_ld_i.eq(1) # indicate LD
- yield port1.pi.addr.data.eq(addr) # set address
- yield port1.pi.addr.ok.eq(1) # set ok
+ yield port1.pi.addr.data.eq(addr) # set address
+ yield port1.pi.addr.ok.eq(1) # set ok
yield from wait_addr(port1) # wait until addr ok
yield from wait_ldok(port1) # wait until ld ok
data = yield port1.pi.ld.data
# cleanup
- yield port1.pi.is_ld_i.eq(0) #end
- yield port1.pi.addr.ok.eq(0) # set !ok
- yield from wait_busy(port1, no=True) # wait until not busy
+ yield port1.pi.is_ld_i.eq(0) # end
+ yield port1.pi.addr.ok.eq(0) # set !ok
+ # yield from wait_busy(port1, no=False) # wait until not busy
return data
yield
addr = 0x2
data = 0xbeef
+ data2 = 0xf00f
#data = 0x4
- yield from l0_cache_st(dut, addr, data)
- result = yield from l0_cache_ld(dut, addr, data)
+ yield from l0_cache_st(dut, 0x2, data)
+ yield from l0_cache_st(dut, 0x3, data2)
+ result = yield from l0_cache_ld(dut, 0x2, data)
+ result2 = yield from l0_cache_ld(dut, 0x3, data2)
yield
+ assert data == result, "data %x != %x" % (result, data)
+ assert data2 == result2, "data2 %x != %x" % (result2, data2)
+
+def data_merger_merge(dut):
+ print("data_merger")
+ #starting with all inputs zero
+ en = yield dut.data_o.en
+ data = yield dut.data_o.data
+ assert en == 0, "en must be zero"
+ assert data == 0, "data must be zero"
yield
+ yield dut.addr_array_i[0].eq(0xFF)
+ for j in range(dut.array_size):
+ yield dut.data_i[j].en.eq(1 << j)
+ yield dut.data_i[j].data.eq(0xFF << (16*j))
+ yield
+ en = yield dut.data_o.en
+ data = yield dut.data_o.data
+ assert data == 0xff00ff00ff00ff00ff00ff00ff00ff
+ assert en == 0xff
yield
- assert data == result, "data %x != %x" % (result, data)
-
def test_l0_cache():
run_simulation(dut, l0_cache_ldst(dut),
vcd_name='test_l0_cache_basic.vcd')
+def test_data_merger():
+
+ dut = DataMerger(8)
+ #vl = rtlil.convert(dut, ports=dut.ports())
+ #with open("test_data_merger.il", "w") as f:
+ # f.write(vl)
+
+ run_simulation(dut, data_merger_merge(dut),
+ vcd_name='test_data_merger.vcd')
+
if __name__ == '__main__':
test_l0_cache()
+ test_data_merger()
projects / soc.git / blobdiff