3 not in any way intended for production use. connects up FunctionUnits to
4 Register Files in a brain-dead fashion that only permits one and only one
5 Function Unit to be operational.
7 the principle here is to take the Function Units, analyse their regspecs,
8 and turn their requirements for access to register file read/write ports
9 into groupings by Register File and Register File Port name.
11 under each grouping - by regfile/port - a list of Function Units that
12 need to connect to that port is created. as these are a contended
13 resource a "Broadcast Bus" per read/write port is then also created,
14 with access to it managed by a PriorityPicker.
16 the brain-dead part of this module is that even though there is no
17 conflict of access, regfile read/write hazards are *not* analysed,
18 and consequently it is safer to wait for the Function Unit to complete
19 before allowing a new instruction to proceed.
22 from nmigen
import Elaboratable
, Module
, Signal
, ResetSignal
, Cat
, Mux
23 from nmigen
.cli
import rtlil
25 from openpower
.decoder
.power_decoder2
import PowerDecodeSubset
26 from openpower
.decoder
.power_regspec_map
import regspec_decode_read
27 from openpower
.decoder
.power_regspec_map
import regspec_decode_write
28 from openpower
.sv
.svp64
import SVP64Rec
30 from nmutil
.picker
import PriorityPicker
31 from nmutil
.util
import treereduce
32 from nmutil
.singlepipe
import ControlBase
34 from soc
.fu
.compunits
.compunits
import AllFunctionUnits
35 from soc
.regfile
.regfiles
import RegFiles
36 from openpower
.decoder
.power_decoder2
import get_rdflags
37 from soc
.experiment
.l0_cache
import TstL0CacheBuffer
# test only
38 from soc
.config
.test
.test_loadstore
import TestMemPspec
39 from openpower
.decoder
.power_enums
import MicrOp
, Function
40 from soc
.simple
.core_data
import CoreInput
, CoreOutput
42 from collections
import defaultdict
45 from nmutil
.util
import rising_edge
48 # helper function for reducing a list of signals down to a parallel
50 def ortreereduce(tree
, attr
="o_data"):
51 return treereduce(tree
, operator
.or_
, lambda x
: getattr(x
, attr
))
54 def ortreereduce_sig(tree
):
55 return treereduce(tree
, operator
.or_
, lambda x
: x
)
58 # helper function to place full regs declarations first
59 def sort_fuspecs(fuspecs
):
61 for (regname
, fspec
) in fuspecs
.items():
62 if regname
.startswith("full"):
63 res
.append((regname
, fspec
))
64 for (regname
, fspec
) in fuspecs
.items():
65 if not regname
.startswith("full"):
66 res
.append((regname
, fspec
))
67 return res
# enumerate(res)
70 # derive from ControlBase rather than have a separate Stage instance,
71 # this is simpler to do
72 class NonProductionCore(ControlBase
):
73 def __init__(self
, pspec
):
76 # test is SVP64 is to be enabled
77 self
.svp64_en
= hasattr(pspec
, "svp64") and (pspec
.svp64
== True)
79 # test to see if regfile ports should be reduced
80 self
.regreduce_en
= (hasattr(pspec
, "regreduce") and
81 (pspec
.regreduce
== True))
84 self
.make_hazard_vecs
= True
85 self
.core_type
= "fsm"
86 if hasattr(pspec
, "core_type"):
87 self
.core_type
= pspec
.core_type
89 super().__init
__(stage
=self
)
91 # single LD/ST funnel for memory access
92 self
.l0
= l0
= TstL0CacheBuffer(pspec
, n_units
=1)
95 # function units (only one each)
96 # only include mmu if enabled in pspec
97 self
.fus
= AllFunctionUnits(pspec
, pilist
=[pi
])
99 # link LoadStore1 into MMU
100 mmu
= self
.fus
.get_fu('mmu0')
101 print ("core pspec", pspec
.ldst_ifacetype
)
102 print ("core mmu", mmu
)
104 print ("core lsmem.lsi", l0
.cmpi
.lsmem
.lsi
)
105 mmu
.alu
.set_ldst_interface(l0
.cmpi
.lsmem
.lsi
)
107 # register files (yes plural)
108 self
.regs
= RegFiles(pspec
, make_hazard_vecs
=self
.make_hazard_vecs
)
110 # set up input and output: unusual requirement to set data directly
111 # (due to the way that the core is set up in a different domain,
112 # see TestIssuer.setup_peripherals
113 self
.i
, self
.o
= self
.new_specs(None)
114 self
.i
, self
.o
= self
.p
.i_data
, self
.n
.o_data
116 # create per-FU instruction decoders (subsetted). these "satellite"
117 # decoders reduce wire fan-out from the one (main) PowerDecoder2
118 # (used directly by the trap unit) to the *twelve* (or more)
119 # Function Units. we can either have 32 wires (the instruction)
120 # to each, or we can have well over a 200 wire fan-out (to 12
121 # ALUs). it's an easy choice to make.
125 for funame
, fu
in self
.fus
.fus
.items():
126 f_name
= fu
.fnunit
.name
127 fnunit
= fu
.fnunit
.value
128 opkls
= fu
.opsubsetkls
130 # TRAP decoder is the *main* decoder
131 self
.trapunit
= funame
133 self
.decoders
[funame
] = PowerDecodeSubset(None, opkls
, f_name
,
136 svp64_en
=self
.svp64_en
,
137 regreduce_en
=self
.regreduce_en
)
138 self
.des
[funame
] = self
.decoders
[funame
].do
140 # share the SPR decoder with the MMU if it exists
141 if "mmu0" in self
.decoders
:
142 self
.decoders
["mmu0"].mmu0_spr_dec
= self
.decoders
["spr0"]
144 # next 3 functions are Stage API Compliance
145 def setup(self
, m
, i
):
149 return CoreInput(self
.pspec
, self
.svp64_en
, self
.regreduce_en
)
154 # elaborate function to create HDL
155 def elaborate(self
, platform
):
156 m
= super().elaborate(platform
)
158 # for testing purposes, to cut down on build time in coriolis2
159 if hasattr(self
.pspec
, "nocore") and self
.pspec
.nocore
== True:
160 x
= Signal() # dummy signal
165 m
.submodules
.fus
= self
.fus
166 m
.submodules
.l0
= l0
= self
.l0
167 self
.regs
.elaborate_into(m
, platform
)
172 self
.connect_satellite_decoders(m
)
174 # ssh, cheat: trap uses the main decoder because of the rewriting
175 self
.des
[self
.trapunit
] = self
.i
.e
.do
177 # connect up Function Units, then read/write ports
178 fu_bitdict
, fu_selected
= self
.connect_instruction(m
)
179 self
.connect_rdports(m
, fu_selected
)
180 self
.connect_wrports(m
, fu_selected
)
182 # note if an exception happened. in a pipelined or OoO design
183 # this needs to be accompanied by "shadowing" (or stalling)
185 for exc
in self
.fus
.excs
.values():
186 el
.append(exc
.happened
)
187 if len(el
) > 0: # at least one exception
188 comb
+= self
.o
.exc_happened
.eq(Cat(*el
).bool())
192 def connect_satellite_decoders(self
, m
):
194 for k
, v
in self
.decoders
.items():
195 # connect each satellite decoder and give it the instruction.
196 # as subset decoders this massively reduces wire fanout given
197 # the large number of ALUs
198 setattr(m
.submodules
, "dec_%s" % v
.fn_name
, v
)
199 comb
+= v
.dec
.raw_opcode_in
.eq(self
.i
.raw_insn_i
)
200 comb
+= v
.dec
.bigendian
.eq(self
.i
.bigendian_i
)
201 # sigh due to SVP64 RA_OR_ZERO detection connect these too
202 comb
+= v
.sv_a_nz
.eq(self
.i
.sv_a_nz
)
204 comb
+= v
.pred_sm
.eq(self
.i
.sv_pred_sm
)
205 comb
+= v
.pred_dm
.eq(self
.i
.sv_pred_dm
)
206 if k
!= self
.trapunit
:
207 comb
+= v
.sv_rm
.eq(self
.i
.sv_rm
) # pass through SVP64 ReMap
208 comb
+= v
.is_svp64_mode
.eq(self
.i
.is_svp64_mode
)
209 # only the LDST PowerDecodeSubset *actually* needs to
210 # know to use the alternative decoder. this is all
212 if k
.lower().startswith("ldst"):
213 comb
+= v
.use_svp64_ldst_dec
.eq(
214 self
.i
.use_svp64_ldst_dec
)
216 def connect_instruction(self
, m
):
217 """connect_instruction
219 uses decoded (from PowerOp) function unit information from CSV files
220 to ascertain which Function Unit should deal with the current
223 some (such as OP_ATTN, OP_NOP) are dealt with here, including
224 ignoring it and halting the processor. OP_NOP is a bit annoying
225 because the issuer expects busy flag still to be raised then lowered.
226 (this requires a fake counter to be set).
228 comb
, sync
= m
.d
.comb
, m
.d
.sync
231 # indicate if core is busy
232 busy_o
= self
.o
.busy_o
234 # enable/busy-signals for each FU, get one bit for each FU (by name)
235 fu_enable
= Signal(len(fus
), reset_less
=True)
236 fu_busy
= Signal(len(fus
), reset_less
=True)
239 for i
, funame
in enumerate(fus
.keys()):
240 fu_bitdict
[funame
] = fu_enable
[i
]
241 fu_selected
[funame
] = fu_busy
[i
]
243 # identify function units and create a list by fnunit so that
244 # PriorityPickers can be created for selecting one of them that
245 # isn't busy at the time the incoming instruction needs passing on
246 by_fnunit
= defaultdict(list)
247 for fname
, member
in Function
.__members
__.items():
248 for funame
, fu
in fus
.items():
249 fnunit
= fu
.fnunit
.value
250 if member
.value
& fnunit
: # this FU handles this type of op
251 by_fnunit
[fname
].append((funame
, fu
)) # add by Function
253 # ok now just print out the list of FUs by Function, because we can
254 for fname
, fu_list
in by_fnunit
.items():
255 print ("FUs by type", fname
, fu_list
)
257 # now create a PriorityPicker per FU-type such that only one
258 # non-busy FU will be picked
260 fu_found
= Signal() # take a note if no Function Unit was available
261 for fname
, fu_list
in by_fnunit
.items():
262 i_pp
= PriorityPicker(len(fu_list
))
263 m
.submodules
['i_pp_%s' % fname
] = i_pp
265 for i
, (funame
, fu
) in enumerate(fu_list
):
266 # match the decoded instruction (e.do.fn_unit) against the
267 # "capability" of this FU, gate that by whether that FU is
268 # busy, and drop that into the PriorityPicker.
269 # this will give us an output of the first available *non-busy*
270 # Function Unit (Reservation Statio) capable of handling this
272 fnunit
= fu
.fnunit
.value
273 en_req
= Signal(name
="issue_en_%s" % funame
, reset_less
=True)
274 fnmatch
= (self
.i
.e
.do
.fn_unit
& fnunit
).bool()
275 comb
+= en_req
.eq(fnmatch
& ~fu
.busy_o
& self
.p
.i_valid
)
276 i_l
.append(en_req
) # store in list for doing the Cat-trick
277 # picker output, gated by enable: store in fu_bitdict
278 po
= Signal(name
="o_issue_pick_"+funame
) # picker output
279 comb
+= po
.eq(i_pp
.o
[i
] & i_pp
.en_o
)
280 comb
+= fu_bitdict
[funame
].eq(po
)
281 comb
+= fu_selected
[funame
].eq(fu
.busy_o | po
)
282 # if we don't do this, then when there are no FUs available,
283 # the "p.o_ready" signal will go back "ok we accepted this
284 # instruction" which of course isn't true.
285 comb
+= fu_found
.eq(~fnmatch | i_pp
.en_o
)
286 # for each input, Cat them together and drop them into the picker
287 comb
+= i_pp
.i
.eq(Cat(*i_l
))
289 # sigh - need a NOP counter
291 with m
.If(counter
!= 0):
292 sync
+= counter
.eq(counter
- 1)
295 with m
.If(self
.p
.i_valid
): # run only when valid
296 with m
.Switch(self
.i
.e
.do
.insn_type
):
297 # check for ATTN: halt if true
298 with m
.Case(MicrOp
.OP_ATTN
):
299 m
.d
.sync
+= self
.o
.core_terminate_o
.eq(1)
301 # fake NOP - this isn't really used (Issuer detects NOP)
302 with m
.Case(MicrOp
.OP_NOP
):
303 sync
+= counter
.eq(2)
307 # connect up instructions. only one enabled at a time
308 for funame
, fu
in fus
.items():
309 do
= self
.des
[funame
]
310 enable
= fu_bitdict
[funame
]
312 # run this FunctionUnit if enabled
313 # route op, issue, busy, read flags and mask to FU
315 # operand comes from the *local* decoder
316 comb
+= fu
.oper_i
.eq_from(do
)
317 comb
+= fu
.issue_i
.eq(1) # issue when input valid
318 # rdmask, which is for registers, needs to come
319 # from the *main* decoder
320 rdmask
= get_rdflags(self
.i
.e
, fu
)
321 comb
+= fu
.rdmaskn
.eq(~rdmask
)
323 # if instruction is busy, set busy output for core.
324 busys
= map(lambda fu
: fu
.busy_o
, fus
.values())
325 comb
+= busy_o
.eq(Cat(*busys
).bool())
327 # ready/valid signalling. if busy, means refuse incoming issue.
328 # (this is a global signal, TODO, change to one which allows
329 # overlapping instructions)
330 # also, if there was no fu found we must not send back a valid
331 # indicator. BUT, of course, when there is no instruction
332 # we must ignore the fu_found flag, otherwise o_ready will never
333 # be set when everything is idle
334 comb
+= self
.p
.o_ready
.eq(fu_found | ~self
.p
.i_valid
)
336 # return both the function unit "enable" dict as well as the "busy".
337 # the "busy-or-issued" can be passed in to the Read/Write port
338 # connecters to give them permission to request access to regfiles
339 return fu_bitdict
, fu_selected
341 def connect_rdport(self
, m
, fu_bitdict
, rdpickers
, regfile
, regname
, fspec
):
342 comb
, sync
= m
.d
.comb
, m
.d
.sync
348 # select the required read port. these are pre-defined sizes
349 rfile
= regs
.rf
[regfile
.lower()]
350 rport
= rfile
.r_ports
[rpidx
]
351 print("read regfile", rpidx
, regfile
, regs
.rf
.keys(),
355 if not isinstance(fspecs
, list):
362 for i
, fspec
in enumerate(fspecs
):
363 # get the regfile specs for this regfile port
364 (rf
, read
, write
, wid
, fuspec
) = fspec
365 print ("fpsec", i
, fspec
, len(fuspec
))
366 ppoffs
.append(pplen
) # record offset for picker
368 name
= "rdflag_%s_%s_%d" % (regfile
, regname
, i
)
369 rdflag
= Signal(name
=name
, reset_less
=True)
370 comb
+= rdflag
.eq(rf
)
371 rdflags
.append(rdflag
)
374 print ("pplen", pplen
)
376 # create a priority picker to manage this port
377 rdpickers
[regfile
][rpidx
] = rdpick
= PriorityPicker(pplen
)
378 setattr(m
.submodules
, "rdpick_%s_%s" % (regfile
, rpidx
), rdpick
)
382 for i
, fspec
in enumerate(fspecs
):
383 (rf
, read
, write
, wid
, fuspec
) = fspec
384 # connect up the FU req/go signals, and the reg-read to the FU
385 # and create a Read Broadcast Bus
386 for pi
, (funame
, fu
, idx
) in enumerate(fuspec
):
389 # connect request-read to picker input, and output to go-rd
390 fu_active
= fu_bitdict
[funame
]
391 name
= "%s_%s_%s_%i" % (regfile
, rpidx
, funame
, pi
)
392 addr_en
= Signal
.like(reads
[i
], name
="addr_en_"+name
)
393 pick
= Signal(name
="pick_"+name
) # picker input
394 rp
= Signal(name
="rp_"+name
) # picker output
395 delay_pick
= Signal(name
="dp_"+name
) # read-enable "underway"
397 # exclude any currently-enabled read-request (mask out active)
398 comb
+= pick
.eq(fu
.rd_rel_o
[idx
] & fu_active
& rdflags
[i
] &
400 comb
+= rdpick
.i
[pi
].eq(pick
)
401 comb
+= fu
.go_rd_i
[idx
].eq(delay_pick
) # pass in *delayed* pick
403 # if picked, select read-port "reg select" number to port
404 comb
+= rp
.eq(rdpick
.o
[pi
] & rdpick
.en_o
)
405 sync
+= delay_pick
.eq(rp
) # delayed "pick"
406 comb
+= addr_en
.eq(Mux(rp
, reads
[i
], 0))
408 # the read-enable happens combinatorially (see mux-bus below)
409 # but it results in the data coming out on a one-cycle delay.
413 addrs
.append(addr_en
)
416 # use the *delayed* pick signal to put requested data onto bus
417 with m
.If(delay_pick
):
418 # connect regfile port to input, creating fan-out Bus
420 print("reg connect widths",
421 regfile
, regname
, pi
, funame
,
422 src
.shape(), rport
.o_data
.shape())
423 # all FUs connect to same port
424 comb
+= src
.eq(rport
.o_data
)
426 # or-reduce the muxed read signals
428 # for unary-addressed
429 comb
+= rport
.ren
.eq(ortreereduce_sig(rens
))
431 # for binary-addressed
432 comb
+= rport
.addr
.eq(ortreereduce_sig(addrs
))
433 comb
+= rport
.ren
.eq(Cat(*rens
).bool())
434 print ("binary", regfile
, rpidx
, rport
, rport
.ren
, rens
, addrs
)
436 def connect_rdports(self
, m
, fu_bitdict
):
437 """connect read ports
439 orders the read regspecs into a dict-of-dicts, by regfile, by
440 regport name, then connects all FUs that want that regport by
441 way of a PriorityPicker.
443 comb
, sync
= m
.d
.comb
, m
.d
.sync
447 # dictionary of lists of regfile read ports
448 byregfiles_rd
, byregfiles_rdspec
= self
.get_byregfiles(True)
450 # okaay, now we need a PriorityPicker per regfile per regfile port
451 # loootta pickers... peter piper picked a pack of pickled peppers...
453 for regfile
, spec
in byregfiles_rd
.items():
454 fuspecs
= byregfiles_rdspec
[regfile
]
455 rdpickers
[regfile
] = {}
457 # argh. an experiment to merge RA and RB in the INT regfile
458 # (we have too many read/write ports)
459 if self
.regreduce_en
:
461 fuspecs
['rabc'] = [fuspecs
.pop('rb')]
462 fuspecs
['rabc'].append(fuspecs
.pop('rc'))
463 fuspecs
['rabc'].append(fuspecs
.pop('ra'))
464 if regfile
== 'FAST':
465 fuspecs
['fast1'] = [fuspecs
.pop('fast1')]
466 if 'fast2' in fuspecs
:
467 fuspecs
['fast1'].append(fuspecs
.pop('fast2'))
468 if 'fast3' in fuspecs
:
469 fuspecs
['fast1'].append(fuspecs
.pop('fast3'))
471 # for each named regfile port, connect up all FUs to that port
472 for (regname
, fspec
) in sort_fuspecs(fuspecs
):
473 print("connect rd", regname
, fspec
)
474 self
.connect_rdport(m
, fu_bitdict
, rdpickers
, regfile
,
477 def connect_wrport(self
, m
, fu_bitdict
, wrpickers
, regfile
, regname
, fspec
):
478 comb
, sync
= m
.d
.comb
, m
.d
.sync
482 print("connect wr", regname
, fspec
)
485 # select the required write port. these are pre-defined sizes
486 print(regfile
, regs
.rf
.keys())
487 rfile
= regs
.rf
[regfile
.lower()]
488 wport
= rfile
.w_ports
[rpidx
]
491 if not isinstance(fspecs
, list):
497 for i
, fspec
in enumerate(fspecs
):
498 # get the regfile specs for this regfile port
499 (rf
, read
, write
, wid
, fuspec
) = fspec
500 print ("fpsec", i
, fspec
, len(fuspec
))
501 ppoffs
.append(pplen
) # record offset for picker
504 # create a priority picker to manage this port
505 wrpickers
[regfile
][rpidx
] = wrpick
= PriorityPicker(pplen
)
506 setattr(m
.submodules
, "wrpick_%s_%s" % (regfile
, rpidx
), wrpick
)
511 for i
, fspec
in enumerate(fspecs
):
512 # connect up the FU req/go signals and the reg-read to the FU
513 # these are arbitrated by Data.ok signals
514 (rf
, read
, write
, wid
, fuspec
) = fspec
515 for pi
, (funame
, fu
, idx
) in enumerate(fuspec
):
518 # write-request comes from dest.ok
519 dest
= fu
.get_out(idx
)
520 fu_dest_latch
= fu
.get_fu_out(idx
) # latched output
521 name
= "wrflag_%s_%s_%d" % (funame
, regname
, idx
)
522 wrflag
= Signal(name
=name
, reset_less
=True)
523 comb
+= wrflag
.eq(dest
.ok
& fu
.busy_o
)
525 # connect request-write to picker input, and output to go-wr
526 fu_active
= fu_bitdict
[funame
]
527 pick
= fu
.wr
.rel_o
[idx
] & fu_active
# & wrflag
528 comb
+= wrpick
.i
[pi
].eq(pick
)
529 # create a single-pulse go write from the picker output
530 wr_pick
= Signal(name
="wpick_%s_%s_%d" % (funame
, regname
, idx
))
531 comb
+= wr_pick
.eq(wrpick
.o
[pi
] & wrpick
.en_o
)
532 comb
+= fu
.go_wr_i
[idx
].eq(rising_edge(m
, wr_pick
))
534 # connect the regspec write "reg select" number to this port
535 # only if one FU actually requests (and is granted) the port
536 # will the write-enable be activated
537 addr_en
= Signal
.like(write
)
539 comb
+= wp
.eq(wr_pick
& wrpick
.en_o
)
540 comb
+= addr_en
.eq(Mux(wp
, write
, 0))
544 addrs
.append(addr_en
)
547 # connect regfile port to input
548 print("reg connect widths",
549 regfile
, regname
, pi
, funame
,
550 dest
.shape(), wport
.i_data
.shape())
551 wsigs
.append(fu_dest_latch
)
553 # here is where we create the Write Broadcast Bus. simple, eh?
554 comb
+= wport
.i_data
.eq(ortreereduce_sig(wsigs
))
556 # for unary-addressed
557 comb
+= wport
.wen
.eq(ortreereduce_sig(wens
))
559 # for binary-addressed
560 comb
+= wport
.addr
.eq(ortreereduce_sig(addrs
))
561 comb
+= wport
.wen
.eq(ortreereduce_sig(wens
))
563 def connect_wrports(self
, m
, fu_bitdict
):
564 """connect write ports
566 orders the write regspecs into a dict-of-dicts, by regfile,
567 by regport name, then connects all FUs that want that regport
568 by way of a PriorityPicker.
570 note that the write-port wen, write-port data, and go_wr_i all need to
571 be on the exact same clock cycle. as there is a combinatorial loop bug
572 at the moment, these all use sync.
574 comb
, sync
= m
.d
.comb
, m
.d
.sync
577 # dictionary of lists of regfile write ports
578 byregfiles_wr
, byregfiles_wrspec
= self
.get_byregfiles(False)
580 # same for write ports.
581 # BLECH! complex code-duplication! BLECH!
583 for regfile
, spec
in byregfiles_wr
.items():
584 fuspecs
= byregfiles_wrspec
[regfile
]
585 wrpickers
[regfile
] = {}
587 if self
.regreduce_en
:
588 # argh, more port-merging
590 fuspecs
['o'] = [fuspecs
.pop('o')]
591 fuspecs
['o'].append(fuspecs
.pop('o1'))
592 if regfile
== 'FAST':
593 fuspecs
['fast1'] = [fuspecs
.pop('fast1')]
594 if 'fast2' in fuspecs
:
595 fuspecs
['fast1'].append(fuspecs
.pop('fast2'))
596 if 'fast3' in fuspecs
:
597 fuspecs
['fast1'].append(fuspecs
.pop('fast3'))
599 for (regname
, fspec
) in sort_fuspecs(fuspecs
):
600 self
.connect_wrport(m
, fu_bitdict
, wrpickers
,
601 regfile
, regname
, fspec
)
603 def get_byregfiles(self
, readmode
):
605 mode
= "read" if readmode
else "write"
608 e
= self
.i
.e
# decoded instruction to execute
610 # dictionary of lists of regfile ports
613 for (funame
, fu
) in fus
.items():
614 print("%s ports for %s" % (mode
, funame
))
615 for idx
in range(fu
.n_src
if readmode
else fu
.n_dst
):
617 (regfile
, regname
, wid
) = fu
.get_in_spec(idx
)
619 (regfile
, regname
, wid
) = fu
.get_out_spec(idx
)
620 print(" %d %s %s %s" % (idx
, regfile
, regname
, str(wid
)))
622 rdflag
, read
= regspec_decode_read(e
, regfile
, regname
)
625 rdflag
, read
= None, None
626 wrport
, write
= regspec_decode_write(e
, regfile
, regname
)
627 if regfile
not in byregfiles
:
628 byregfiles
[regfile
] = {}
629 byregfiles_spec
[regfile
] = {}
630 if regname
not in byregfiles_spec
[regfile
]:
631 byregfiles_spec
[regfile
][regname
] = \
632 (rdflag
, read
, write
, wid
, [])
633 # here we start to create "lanes"
634 if idx
not in byregfiles
[regfile
]:
635 byregfiles
[regfile
][idx
] = []
636 fuspec
= (funame
, fu
, idx
)
637 byregfiles
[regfile
][idx
].append(fuspec
)
638 byregfiles_spec
[regfile
][regname
][4].append(fuspec
)
640 # ok just print that out, for convenience
641 for regfile
, spec
in byregfiles
.items():
642 print("regfile %s ports:" % mode
, regfile
)
643 fuspecs
= byregfiles_spec
[regfile
]
644 for regname
, fspec
in fuspecs
.items():
645 [rdflag
, read
, write
, wid
, fuspec
] = fspec
646 print(" rf %s port %s lane: %s" % (mode
, regfile
, regname
))
647 print(" %s" % regname
, wid
, read
, write
, rdflag
)
648 for (funame
, fu
, idx
) in fuspec
:
649 fusig
= fu
.src_i
[idx
] if readmode
else fu
.dest
[idx
]
650 print(" ", funame
, fu
, idx
, fusig
)
653 return byregfiles
, byregfiles_spec
656 yield from self
.fus
.ports()
657 yield from self
.i
.e
.ports()
658 yield from self
.l0
.ports()
665 if __name__
== '__main__':
666 pspec
= TestMemPspec(ldst_ifacetype
='testpi',
671 dut
= NonProductionCore(pspec
)
672 vl
= rtlil
.convert(dut
, ports
=dut
.ports())
673 with
open("test_core.il", "w") as f
: